OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

JN5148/001M03T,534

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P23
2. Specifications
Most specification parameters for the modules are specified in the chip datasheet - JN-DS-JN5148 Wireless
Microcontroller Datasheet
, [2]. Where there are differences, the parameters are defined here.
VDD=3.0V @ +25°C
Typical DC Characteristics Notes
JN5148-001-
M00/03
JN5148-001-
M04
Deep sleep current 1.3uA 1.3uA
Sleep current 2.6uA 2.6uA With active sleep timer
Radio transmit current 15mA 110mA CPU in doze, radio transmitting
Radio receive current 17.5mA 23mA CPU in doze, radio receiving
Centre frequency accuracy +/-25ppm +/-25ppm
Additional +/-15ppm allowance for
temperature and ageing
Typical RF Characteristics Notes
Receive sensitivity -95dBm -98dBm
Nominal for 1% PER, as per
802.15.4 section 6.5.3.3 (Note 1)
Maximum Transmit power +2.5dBm 18dBm Nominal (Note 1)
Transmit power at 3.6V 20dBm With Vdd=3.6V
Maximum input signal +5dBm -5dBm
For 1% PER, measured as
sensitivity
RSSI range
-95 to -10
dBm
-105 to -20
dBm
RF Port impedance – uFl connector 50 ohm 50 ohm 2.4 - 2.5GHz
VSWR (max) 2:1 2:1 2.4 - 2.5GHz
Peripherals Notes
Master SPI port 5 selects 3 selects 250kHz - 16MHz
Slave SPI port
9 9
250kHz - 8MHz
Two UARTs
9 9
16550 compatible
Two-wire serial I/F (compatible with SMbus & I
2
C)
9 9
Up to 400kHz
Two programmable Timer/Counters with
capture/compare facility, Tick timer
9 9
16MHz clock
Two programmable Sleep Timers
9 9
32kHz clock
Digital IO lines (multiplexed with UARTs, timers
and SPI selects)
21 19
Four channel Analogue-to-Digital converter
9 9
12-bit, up to 100ks/s
Two channel Digital-to-Analogue converter
9 9
12-bit, up to 100ks/s
Two programmable analogue comparators
9 9
Ultra low power mode for sleep
Internal temperature sensor and battery monitor
9 9
The performance of all peripherals is defined in the JN-DS-JN5148 Wireless Microcontroller Datasheet [2]
Note 1: Sensitivity is defined for conducted measurements on connectorised modules. Modules with an integrated
antenna have approximately 4 dB less e.i.r.p and reciprocal receive sensitivity.
4 JN-DS-JN5148-001-Myy 1v4 © NXP Laboratories UK 2010
3. Product Development
Jennic supplies all the development tools and networking stacks needed to enable end-product development to occur
quickly and efficiently. These are all freely available from www.nxp.com/jennic. A range of evaluation/developer kits
is also available, allowing products to be quickly bread boarded. Efficient development of software applications is
enabled by the provision of a complete, unlimited, software developer kit. Together with the available libraries for the
IEEE802.15.4 MAC and the JenNet and ZigBee PRO network stacks, this package provides everything required to
develop application code and to trial it with hardware representative of the final module.
The modules can be user programmed both in development and in production using software supplied by Jennic.
Access to the on-chip peripherals, MAC and network stack software is provided through specific APIs. This
information is available on the Jennic support website, together with many example applications, user guides,
reference manuals and application notes.
3.1. JN5148 Single Chip Wireless Microcontroller
The JN5148-001-Myy series is constructed around the JN5148-001 single chip wireless microcontroller, which
includes the radio system, a 32-bit RISC CPU, ROM and RAM memory and a range of analogue and digital
peripherals.
The chip is described fully in
JN-DS-JN5148 Wireless Microcontroller Datasheet [2].
The module also includes a 4Mbit serial flash memory, which holds the application code that is loaded into the
JN5148 during the boot sequence and provides static data storage, required by the application.
© NXP Laboratories UK 2010 JN-DS-JN5148-001-Myy 1v4 5
4. Pin Configurations
1
2
3
4
16
ADC4
DAC1
DAC2
COMP2+
COMP2-
SPICLK
SPIMISO
SPIMOSI
SPISSZ
DIO0
DIO1
DIO2
SPISSM
SPISWP
DIO3
DIO4
DIO5
DIO6
DIO7
DIO8
DIO9
DIO10
DIO11
VDD
GND
VSSA
ADC3
ADC2
ADC1
DIO20
DIO19
DIO18
DIO17
DIO16
DIO15
RESETN
DIO14
DIO13
DIO12
5
6
7
8
9
10
11
12
13
14
15
17 18 19 20 21 22 23 24 25 26
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
COMP1+
COMP1-
Figure 1: Pin Configuration (top view)
Note that the same basic pin configuration applies for all module designs. However, DIO3 and DIO2 are not available
on the high power modules.
6 JN-DS-JN5148-001-Myy 1v4 © NXP Laboratories UK 2010
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P23

JN5148/001M03T,534

Mfr. #:
Buy JN5148/001M03T,534
Manufacturer:
NXP Semiconductors
Description:
RF TXRX MODULE 802.15.4 U.FL ANT
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet