14
Pin # Function
1 V
O
2 Ground
3 V
CC
4 R
L
5 Do not connect
8 Do not connect
Note: Pins 5 and 8 are for mounting and retaining purposes only. Do not
electrically connect these pins.
HFBR-25X2Z/25X4Z Receivers
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Reference
Storage Temperature T
S
–40 +85 °C
Operating Temperature T
A
–40 +85 °C
Lead Soldering Cycle Temp. 260 °C Note 1, 3
Time 10 sec
Supply Voltage V
CC
–0.5 7 V Note 2
Output Collector Current I
OAV
25 mA
Output Collector Power Dissipation P
OD
40 mW
Output Voltage V
O
–0.5 18 V
Pull-up Voltage V
P
–5 V
CC
V
Fan Out (TTL) N 5
Notes:
1. 1.6 mm below seating plane.
2. It is essential that a bypass capacitor 0.1 µF be connected from pin 2 to pin 3 of the receiver. Total lead length between both ends of the capacitor
and the pins should not exceed 20 mm.
3. Moisture sensitivity level (MSL) is 3.
Receiver Electrical/Optical Characteristics 0 °C to 70 °C, 4.75 V ≤V
CC
≤5.25 V, unless otherwise specied.
Parameter Symbol Min. Typ. Max. Units Conditions Ref.
Receiver HFBR-2522Z P
R(L)
–24 dBm V
OL
= 0 V Notes 1, 2, 3
Optical Input I
OL
= 8 mA 4, 6
Power Level HFBR-2524Z –20
Logic 0
Optical Input Power P
R(H)
-43 dBm V
OH
= 5.25 V
Level Logic 1 I
OH
= ≤ 250 µA
High Level Output Current I
OH
5 250 µA V
O
= 18 V, P
R
= 0 Notes 5, 6
Low Level Output Voltage V
OL
0.4 0.5 V I
OL
= 8 mA Notes 5, 6
P
R
= P
R(L)MIN
High Level Supply Current I
CCH
3.5 6.3 mA V
CC
= 5.25 V, Notes 5, 6
P
R
= 0
Low Level Supply Current I
CCL
6.2 10 mA V
CC
= 5.25 V, Notes 5, 6
P
R
= -12.5 dBm
Eective Diameter D 1 mm
Numerical Aperture NA 0.5
Internal Pull-up Resistor R
L
680 1000 1700 Ω
Notes:
1. Measured at the end of the ber optic cable with large area detector.
2. Pulsed LED operation at I
F
> 80 mA will cause increased link t
PLH
propagation delay time. This extended t
PLH
time contributes to increased pulse
width distortion of the receiver output signal.
3. The LED drive circuit of Figure 11 is required for 1 MBd operation of the HFBR-25X2Z/25X4Z.
4. Optical ux, P (dBm) = 10 Log [P(µW)/1000 µW].
5. R
L
is open.
6. Guaranteed only if optical input signal to the receiver is generated by HFBR-15x2Z/4Z, with ideal alignment to photodiode using 1 mm POF
(NA=0.5).
4
3
2
1
DO NOT CONNECT 5
DO NOT CONNECT 8
R
L
V
CC
V
O
1000 Ω