9
HFBR-25X1Z Receiver
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Reference
Storage Temperature T
S
–40 +85 °C
Operating Temperature T
A
–40 +85 °C
Lead Soldering Cycle Temp. 260 °C Notes 1, 3
Time 10 sec
Supply Voltage V
CC
–0.5 7 V Note 2
Output Collector Current I
OAV
25 mA
Output Collector Power Dissipation P
OD
40 mW
Output Voltage V
O
–0.5 18 V
Pull-up Voltage V
P
–5 V
CC
V
Fan Out (TTL) N 5
Receiver Electrical/Optical Characteristics 0 °C to 70 °C, 4.75 V ≤ V
CC
≤5.25 V, unless otherwise specied.
Parameter Symbol Min. Typ. Max. Units Conditions Ref.
Input Optical Power P
R(L)
–21.6 –9.5 dBm V
OL
= 0.5 V Notes 1,
Level for Logic “0” I
OL
= 8 mA 2, 4, 5
–21.6 –8.7 V
OL
= 0.5 V
I
OL
= 8 mA, 25 °C
Input Optical Power P
R(H)
–43 dBm V
OL
= 5.25 V Notes 1, 5
Level for Logic “1” I
OH
≤ 250 µA
High Level Output Current I
OH
5 250 µA V
O
= 18 V, P
R
= 0 Notes 3, 5
Low Level Output Current V
OL
0.4 0.5 V I
OL
= 8 mA, Notes 3, 5
P
R
= P
R(L)MIN
High Level Supply I
CCH
3.5 6.3 mA V
CC
= 5.25 V, Notes 3, 5
Current P
R
= 0
Low Level Supply Current I
CCL
6.2 10 mA V
CC
= 5.25 V Notes 3, 5
P
R
= -12.5 dBm
Eective Diameter D 1 mm
Numerical Aperture NA 0.5
Internal Pull-up Resistor R
L
680 1000 1700 Ω
Pin # Function
1 V
O
2 Ground
3 V
CC
4 R
L
5 Do not connect
8 Do not connect
Note: Pins 5 and 8 are for mounting and retaining purposes only. Do not
electrically connect these pins.
4
3
2
1
DO NOT CONNECT 5
DO NOT CONNECT 8
R
L
V
CC
GROUND
V
O
1000 Ω
Notes:
1. 1.6 mm below seating plane.
2. It is essential that a bypass capacitor 0.1 µF be connected from pin 2 to pin 3 of the receiver. Total lead length between both ends of the capacitor
and the pins should not exceed 20 mm.
3. Moisture sensitivity level (MSL) is 3.
Notes:
1. Optical ux, P (dBm) = 10 Log [P (µW)/1000 µW].
2. Measured at the end of the ber optic cable with large area detector.
3. R
L
is open.
4. Pulsed LED operation at I
F
> 80 mA will cause increased link t
PLH
propagation delay time. This extended t
PLH
time contributes to increased pulse
width distortion of the receiver output signal.
5. Guaranteed only if optical input signal to the receiver is generated by HFBR-15x1Z, with ideal alignment to photo diode using 1 mm POF (NA=0.5).