4
FN6397.2
March 20, 2007
Absolute Maximum Ratings Thermal Information
Supply Voltage, V
DD
and V
CC
. . . . . . . . . . . . . . . . . . . . -0.3V to 16V
Logic I/O Voltages . . . . . . . . . . . . . . . . . . . . . . . -0.3V to V
DD
+0.3V
Voltage on AHS, BHS . -6.0V (Transient) to 70V (+25°C to +125°C)
Voltage on AHS, BHS . .-6.0V (Transient) to 70V (-55°C to +125°C)
Voltage on ALS, BLS . . . . . . . -2.0V (Transient) to +2.0V (Transient)
Voltage on AHB, BHB . . . . . . V
AHS, BHS
-0.3V to V
AHS, BHS
+V
DD
Voltage on ALO, BLO. . . . . . . . . . . . .V
ALS, BLS
-0.3V to V
CC
+0.3V
Voltage on AHO, BHO . . . . . . V
AHS, BHS
-0.3V to V
AHB, BHB
+0.3V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . . . . -5mA to 0mA
Phase Slew Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V/ns
All Voltages relative to V
SS
, unless otherwise specified.
Operating Conditions
Supply Voltage, V
DD
and V
CC
. . . . . . . . . . . . . . . . . . +9.5V to +15V
Voltage on ALS, BLS . . . . . . . . . . . . . . . . . . . . . . . . . -1.0V to +1.0V
Voltage on AHB, BHB . . . . . . . .V
AHS, BHS
+5V to V
AHS, BHS
+15V
Voltage on AHs, BHS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60V
Input Current, HDEL and LDEL . . . . . . . . . . . . . . . .-500μA to -50μA
Operating Ambient Temperature Range . . . . . . . . . .-40°C to +85°C
Thermal Resistance (Typical, Note 1) θ
JA
(°C/W)
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Maximum Power Dissipation at +85°C
SOIC Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .470mW
PDIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .530mW
Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C
Operating Max. Junction Temperature. . . . . . . . . . . . . . . . . . +125°C
Lead Temperature (Soldering 10s) . . . . . . . . . . . . . . . . . . . . +300°C
(For SOIC - Lead Tips Only)
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTE:
1. θ
JA
is measured with the component mounted on a low effective thermal conductivity test board in free air. See Tech Brief TB379 for details.
Electrical Specifications V
DD
= V
CC
= V
AHB
= V
BHB
= 12V, V
SS
= V
ALS
= V
BLS
= V
AHS
= V
BHS
= 0V, R
HDEL
= R
LDEL
= 100k, and
T
A
= +25°C, Unless Otherwise Specified
PARAMETERS SYMBOL TEST CONDITIONS
T
J
= +25°C T
J
= -40°C to +125°C
UNITSMIN TYP MAX MIN MAX
SUPPLY CURRENTS AND CHARGE PUMPS
V
DD
Quiescent Current I
DD
IN- = 2.5V, Other Inputs = 0V 8 11 14 7 14 mA
V
DD
Operating Current I
DDO
Outputs switching f = 500kHz, No
Load
81215 8 15mA
V
CC
Quiescent Current I
CC
IN- = 2.5V, Other Inputs = 0V,
I
ALO
= I
BLO
= 0
-2580 - 100μA
V
CC
Operating Current I
CCO
f = 500kHz, No Load 1 1.25 2.0 0.8 3 mA
AHB, BHB Quiescent
Current -Qpump Output
Current
I
AHB
, I
BHB
IN- = 2.5V, Other Inputs = 0V,
I
AHO
=I
BHO
= 0,
V
DD
= V
CC
=V
AHB
= V
BHB
= 10V
-50 -25 -11 -60 -10 μA
AHB, BHB Operating
Current
I
AHBO
,
I
BHBO
f = 500kHz, No Load 0.62 1.2 1.5 0.5 1.9 mA
AHS, BHS, AHB, BHB
Leakage Current
I
HLK
V
BHS
= V
AHS
= 60V,
V
AHB
= V
BHB
= 75V
- 0.02 1.0 - 10 μA
AHB-AHS, BHB-BHS
Qpump Output Voltage
V
AHB
- V
AHS
V
BHB
- V
BHS
I
AHB
= I
AHB
= 0, No Load 11.5 12.6 14.0 10.5 14.5 V
INPUT COMPARATOR PINS: IN+, IN-, OUT
Offset Voltage V
OS
Over Common Mode Voltage
Range
-10 0 +10 -15 +15 mV
Input Bias Current I
IB
00.52 0 4μA
Input Offset Current I
OS
-1 0 +1 -2 +2 μA
Input Common Mode
Voltage Range
CMVR 1 - V
DD
-1.5 1 V
DD
-1.5 V
ISL83204A
