ADUM2201BRIZ-RL Datasheet ADUM2201ARWZ-RL, ADUM2201ARWZ, ADUM2201BRWZ-RL | P7-P9

Data Sheet ADuM2200/ADuM2201

Rev. G | Page 7 of 17

PACKAGE CHARACTERISTICS

Table 13.

Parameter Symbol Min Typ Max Unit Test Conditions/Comments

Resistance (Input-to-Output)

I-O

Capacitance (Input-to-Output)

I-O

2 pF f = 1 MHz

Input Capacitance

4 pF

IC Junction-to-Ambient Thermal Resistance θ

45 °C/W

This device is considered a 2-terminal device: Pin 1 through Pin 8 are shorted together, and Pin 9 through Pin 16 are shorted together.

Input capacitance is from any input data pin to ground.

REGULATORY INFORMATION

The ADuM2200/ADuM2201 are approved by the organizations listed in Table 14. Refer to Table 19 and the Insulation Lifetime section

for more information about the recommended maximum working voltages for specific cross-isolation waveforms and insulation levels.

Table 14.

UL CSA CQC VDE

Recognized Under

UL 1577 Component

Recognition Program

Approved under CSA Component

Acceptance Notice 5A

Approved under CQC11-471543-2012 Certified according to

DIN V VDE V 0884-10

(VDE V 0884-10):2006-12

Single Protection,

5000 V rms Isolation

Voltage

Basic insulation per CSA 60950-1-07 and

IEC 60950-1, 600 V rms (848 V peak)

maximum working voltage

Basic insulation per GB4943.1-2011,

600 V rms (848 V peak) maximum

working voltage, tropical climate,

altitude ≤ 5000 m

Reinforced insulation,

848 V peak

RW-16 package: reinforced insulation per

CSA 60950-1-07 and IEC 60950-1,

380 V rms (537 V peak) maximum

working voltage; reinforced insulation

per IEC 60601-1, 125 V rms (176 V peak)

maximum working voltage

RW-16 package: reinforced insulation

per GB4943.1-2011, 380 V rms

(537 V peak) maximum working

voltage, tropical climate, altitude ≤

5000 m

RI-16-2 package: reinforced insulation per

CSA 60950-1-07 and IEC 60950-1,

400 V rms (565 V peak) maximum

working voltage; reinforced insulation

per IEC 60601-1, 250 V rms (353 V peak)

maximum working voltage

RI-16 package: reinforced insulation

per 400 V rms (565 V peak) maximum

working voltage, tropical climate,

altitude ≤ 5000 m

File E214100 File 205078 File: CQC14001105917 File 2471900-4880-0001

In accordance with UL 1577, each ADuM2200/ADuM2201 is proof tested by applying an insulation test voltage ≥ 6000 V rms for 1 sec (current leakage detection limit = 10 µA).

In accordance with DIN V VDE V 0884-10 (VDE V 0884-10):2006-12, each ADuM2200/ADuM2201 is proof tested by applying an insulation test voltage ≥1592 V peak for 1 sec

(partial discharge detection limit = 5 pC). The asterisk (*) marking branded on the components designates DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 approval.

INSULATION AND SAFETY-RELATED SPECIFICATIONS

Table 15.

Parameter Symbol Value Unit Test Conditions/Comments

Rated Dielectric Insulation Voltage 5000 V rms 1-minute duration

Minimum External Air Gap (Clearance) L(I01) 8.0 min mm Distance measured from input terminals to output

terminals, shortest distance through air along the

PCB mounting plane, as an aid to PC board layout

Minimum External Tracking (Creepage)

L(I02)

Measured from input terminals to output terminals,

shortest distance path along body

RW-16 Package 7.7 min mm

RI-16-2 Package 8.3 min mm

Minimum Internal Distance (Internal Clearance) 0.017 min mm Insulation distance through insulation

Tracking Resistance (Comparative Tracking Index) CTI >400 V DIN IEC 112/VDE 0303, Part 1

Isolation Group II Material Group (DIN VDE 0110, 1/89, Table 1)

ADuM2200/ADuM2201 Data Sheet

Rev. G | Page 8 of 17

INSULATION CHARACTERISTICS (DIN V VDE V 0884-10 (VDE V 0884-10):2006-12)

These isolators are suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by

means of protective circuits. The asterisk (*) marking branded on the components designates DIN V VDE V 0884-10 (VDE V 0884-10):2006-12

approval for 848 V peak working voltage.

Table 16.

Description Test Conditions/Comments Symbol Characteristic Unit

Installation Classification per DIN VDE 0110

For Rated Mains Voltage ≤ 150 V rms I to IV

For Rated Mains Voltage ≤ 300 V rms I to IV

For Rated Mains Voltage ≤ 400 V rms I to IV

Climatic Classification 40/105/21

Pollution Degree per DIN VDE 0110, Table 1 2

Maximum Working Insulation Voltage V

IORM

848 V peak

Input-to-Output Test Voltage, Method B1

IORM

× 1.875 = V

pd(m)

, 100% production test,

ini

= t

= 1 sec, partial discharge < 5 pC

pd(m)

1592 V peak

Input-to-Output Test Voltage, Method A

After Environmental Tests Subgroup 1

IORM

× 1.5 = V

pd(m)

, t

ini

= 60 sec, t

= 10 sec, partial

discharge < 5 pC

pd(m)

1273 V peak

After Input and/or Safety Tests Subgroup 2

and Subgroup 3

IORM

× 1.2 = V

pd(m)

, t

ini

= 60 sec, t

= 10 sec, partial

discharge < 5 pC

pd(m)

1018 V peak

Highest Allowable Overvoltage Transient overvoltage, t

= 10 sec V

6000 V peak

Surge Isolation Voltage V peak = 10 kV, 1.2 μs rise time, 50 μs, 50% fall time V

IOSM

6000 V peak

Safety Limiting Values

Maximum value allowed in the event of a failure;

see Figure 3

Maximum Junction Temperature T

150 °C

Total Power Dissipation at 25°C P

2.78 W

Insulation Resistance at T

= 500 V R

>10

3.0

2.0

1.0

0 50 100 150 200

07235-003

SAFE LIMITING POWER (W)

AMBIENT TEMPERATURE (°C)

2.5

1.5

0.5

Figure 3. Thermal Derating Curve, Dependence of Safety Limiting

Values with Case Temperature per DIN V VDE V 0884-10

RECOMMENDED OPERATING CONDITIONS

Table 17.

Parameter Symbol Min Max Unit

Operating Temperature T

A Grade and B Grade −40 +105 °C

WA Grade and WB Grade −40 +125 °C

Supply Voltages

DD1

, V

DD2

3.0 5.5 V

Input Signal Rise and Fall Times 1.0 ms

All voltages are relative to their respective grounds.

Data Sheet ADuM2200/ADuM2201

Rev. G | Page 9 of 17

ABSOLUTE MAXIMUM RATINGS

Table 18.

Parameter Rating

Storage Temperature (T

) −65°C to +150°C

Ambient Operating Temperature (T

)

−40°C to +125°C

Supply Voltage (V

DD1

, V

DD2

)

−0.5 V to +7.0 V

Input Voltage (V

, V

)

1, 2

−0.5 V to V

DDI

+ 0.5 V

Output Voltage (V

, V

)

1, 2

−0.5 V to V

DDO

+ 0.5 V

Average Output Current per Pin

Side 1 (I

) −18 mA to +18 mA

Side 2 (I

) −22 mA to +22 mA

Common-Mode Transients

−100 kV/µs to +100 kV/µs

All voltages are relative to their respective grounds.

DDI

and V

DDO

refer to the supply voltages on the input and output sides

of a given channel, respectively. See the PCB Layout section.

See Figure 3 for maximum rated current values for various temperatures.

Refers to common-mode transients across the insulation barrier. Common-

mode transients exceeding the absolute maximum rating can cause latch-up

or permanent damage.

Stresses at or above those listed under Absolute Maximum

Ratings may cause permanent damage to the product. This is a

stress rating only; functional operation of the product at these

or any other conditions above those indicated in the operational

section of this specification is not implied. Operation beyond

the maximum operating conditions for extended periods may

affect product reliability.

ESD CAUTION

Table 19. Maximum Continuous Working Voltage

Parameter Max Unit Constraint

AC Voltage, Bipolar Waveform 565 V peak 50-year minimum lifetime

AC Voltage, Unipolar Waveform

Reinforced Insulation 1131 V peak 50-year minimum lifetime

DC Voltage

Reinforced Insulation 1131 V peak 50-year minimum lifetime

Refers to continuous voltage magnitude imposed across the isolation barrier. See the Insulation Lifetime section for more information.

Table 20. ADuM2200 Truth Table (Positive Logic)

Input

DD1

State V

DD2

State V

Output

Notes

H H Powered Powered H H

L L Powered Powered L L

H L Powered Powered H L

L H Powered Powered L H

X X Unpowered Powered H H Outputs return to the input state within

1 µs of V

DDI

power restoration.

X X Powered Unpowered Indeterminate Indeterminate Outputs return to the input state within

1 µs of V

DDO

power restoration.

H is logic high, L is logic low, and X is don’t care.

Table 21. ADuM2201 Truth Table (Positive Logic)

Input

DD1

State V

DD2

State V

Output

Notes

H H Powered Powered H H

L L Powered Powered L L

H L Powered Powered H L

L H Powered Powered L H

Unpowered

Powered

Indeterminate

Outputs return to the input state within

1 µs of V

DDI

power restoration.

X X Powered Unpowered H Indeterminate Outputs return to the input state within

1 µs of V

DDO

power restoration.

H is logic high, L is logic low, and X is don’t care.

P1-P3 P4-P6 P7-P9 P10-P12 P13-P15 P16-P17

ADUM2201BRIZ-RL

Mfr. #:

Buy ADUM2201BRIZ-RL

Manufacturer:

Analog Devices Inc.

Description:

Digital Isolators Dual-CH Digital 5kV

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

ADUM2201BRIZ-RL

ADUM2201BRIZ-RL

Products related to this Datasheet