Table 13: DDR2 I
DD
Specifications and Conditions – 4GB (Die Revision C) (Continued)
Values shown for MT47H256M8 DDR2 SDRAM only and are computed from values specified in the 2Gb (256 Meg x 8) com-
ponent data sheet
Parameter Symbol -1GA
-80E/
-800 -667 Units
Operating one bank active-read-precharge current: I
OUT
= 0mA; BL = 4, CL
= CL (I
DD
), AL = 0;
t
CK =
t
CK (I
DD
),
t
RC =
t
RC (I
DD
),
t
RAS =
t
RAS MIN (I
DD
),
t
RCD =
t
RCD (I
DD
); CKE is HIGH, S# is HIGH between valid commands; Address bus in-
puts are switching; Data pattern is same as I
DD4W
I
DD1
1
856 784 736 mA
Precharge power-down current: All device banks idle;
t
CK =
t
CK (I
DD
); CKE is
LOW; Other control and address bus inputs are stable; Data bus inputs are
floating
I
DD2P
2
192 192 192 mA
Precharge quiet standby current: All device banks idle;
t
CK =
t
CK (I
DD
); CKE
is HIGH, S# is HIGH; Other control and address bus inputs are stable; Data bus
inputs are floating
I
DD2Q
2
560 480 400 mA
Precharge standby current: All device banks idle;
t
CK =
t
CK (I
DD
); CKE is
HIGH, S# is HIGH; Other control and address bus inputs are switching; Data bus
inputs are switching
I
DD2N
2
640 560 480 mA
Active power-down current: All device banks open;
t
CK =
t
CK (I
DD
); CKE is LOW; Other control and address bus inputs are
stable; Data bus inputs are floating
Fast PDN exit
MR[12] = 0
I
DD3P
2
400 400 400 mA
Slow PDN exit
MR[12] = 1
224 224 224
Active standby current: All device banks open;
t
CK =
t
CK (I
DD
),
t
RAS =
t
RAS
MAX (I
DD
),
t
RP =
t
RP (I
DD
); CKE is HIGH, S# is HIGH between valid commands;
Other control and address bus inputs are switching; Data bus inputs are switch-
ing
I
DD3N
2
960 800 720 mA
Operating burst write current: All device banks open; Continuous burst
writes; BL = 4, CL = CL (I
DD
), AL = 0;
t
CK =
t
CK (I
DD
),
t
RAS =
t
RAS MAX (I
DD
),
t
RP =
t
RP (I
DD
); CKE is HIGH, S# is HIGH between valid commands; Address bus inputs
are switching; Data bus inputs are switching
I
DD4W
1
1376 1136 976 mA
Operating burst read current: All device banks open; Continuous burst read,
I
OUT
= 0mA; BL = 4, CL = CL (I
DD
), AL = 0;
t
CK =
t
CK (I
DD
),
t
RAS =
t
RAS MAX (I
DD
),
t
RP =
t
RP (I
DD
); CKE is HIGH, S# is HIGH between valid commands; Address bus
inputs are switching; Data bus inputs are switching
I
DD4R
1
1376 1136 976 mA
Burst refresh current:
t
CK =
t
CK (I
DD
); REFRESH command at every
t
RFC (I
DD
)
interval; CKE is HIGH, S# is HIGH between valid commands; Other control and
address bus inputs are switching; Data bus inputs are switching
I
DD5
1
1496 1456 1416 mA
Self refresh current: CK and CK# at 0V; CKE ≤ 0.2V; Other control and ad-
dress bus inputs are floating; Data bus inputs are floating
I
DD6
2
192 192 192 mA
Operating bank interleave read current: All device banks interleaving
reads; I
OUT
= 0mA; BL = 4, CL = CL (I
DD
), AL =
t
RCD (I
DD
) - 1 ×
t
CK (I
DD
);
t
CK =
t
CK
(I
DD
),
t
RC =
t
RC (I
DD
),
t
RRD =
t
RRD (I
DD
),
t
RCD =
t
RCD (I
DD
); CKE is HIGH, S# is
HIGH between valid commands; Address bus inputs are stable during deselects;
Data bus inputs are switching
I
DD7
1
1936 1856 1696 mA
Notes:
1. Value calculated as one module rank in this operating condition; all other module ranks
in I
DD2P
(CKE LOW) mode.
2. Value calculated reflects all module ranks in this operating condition.
1GB, 2GB, 4GB (x64, DR) 240-Pin DDR2 SDRAM UDIMM
I
DD
Specifications
PDF: 09005aef83b82bc1
htf16c128_256_512x64az – Rev. E 4/14 EN
14
Micron Technology, Inc. reserves the right to change products or specifications without notice.
© 2009 Micron Technology, Inc. All rights reserved.
