228
D2SW-PD2SW-P
■ List of Models
Note Consult your OMRON sales representative for details on SPST-NO and SPST-NC models.
Specifications
■ Ratings
Note The ratings values apply under the following test conditions.
Ambient temperature: 20
±2°C
Ambient humidity: 65
±5%
Operating frequency: 20 operations/min
■
Characteristics
Note: 1. The data given above are initial values.
2. The dielectric strength shown in the table indicates a value for models with a Separator.
3. For the pin plunger models, the above values apply for both the free position and total travel position. For the lever models, the
values apply at the total travel position. Contact opening or closing time is within 1ms.
4. Consult your OMRON sales representative for testing conditions.
5. The test to meet standards checks for water intrusion after immersion for 30 minutes. The test does not check for switching op-
eration underwater. Refer to "Degree of Protection" of "Instructions for Correct Use".
Terminal Solder
terminals
Quick-connect
terminals (#110)
PCB terminals Molded lead wires
Rating Actuator Uneven pitch Even pitch
2A Pin plunger D2SW-P2H D2SW-P2T D2SW-P2D P2SW-P2B D2SW-P2M
Hinge lever D2SW-P2L1H D2SW-P2L1T D2SW-P2L1D D2SW-P2L1B D2SW-P2L1M
Hinge roller le-
ver
D2SW-P2L2H D2SW-P2L2T D2SW-P2L2D D2SW-P2L2B D2SW-P2L2M
Simulated roll-
er lever
D2SW-P2L3H D2SW-P2L3T D2SW-P2L3D D2SW-P2L3B D2SW-P2L3M
0.1A Pin plunger D2SW-P01H D2SW-P01T D2SW-P01D D2SW-P01B D2SW-P01M
Hinge lever D2SW-P01L1H D2SW-P01L1T D2SW-P01L1D D2SW-P01L1B D2SW-P01L1M
Hinge roller le-
ver
D2SW-P01L2H D2SW-P01L2T D2SW-P01L2D D2SW-P01L2B D2SW-P01L2M
Simulated roll-
er lever
D2SW-P01L3H D2SW-P01L3T D2SW-P01L3D D2SW-P01L3B D2SW-P01L3M
Model Rated voltage Resistive load
D2SW-P2 30 VDC 2 A
250 VAC
D2SW-P01 30 VDC 0.1 A
125 VAC
Item Model D2SW-P2 D2SW-P01
Operating speed 0.1 mm to 500 mm/s (pin plunger models)
Operating frequency Machanical : 120 operations/min max.
Electrical : 20 operations/min max.
Insulation resistance 100 M
Ω min. (at 500 VDC)
Contact resistance (initial value) Terminal models : 50 m
Ω max.
Molded lead wire models : 100 m
Ω max.
Terminal models : 100 m
Ω max.
Molded lead wire models : 150 m
Ω max.
Dielectric strength (see note 2) 1,000 VAC, 50/60 Hz for 1 min between terminals
of the same polarities
600 VAC, 50/60 Hz for 1 min between terminals
of the same polarities
1,500 VAC, 50/60 Hz for 1 min between current-carrying metal parts and ground, and between each
terminal and non-current-carrying metal parts
Vibration resistance (see note 3) Malfunction: 10 to 55 Hz, 1.5-mm double amplitude
Shock resistance (see note 3)
Destruction: 1,000 m/s
2
{approx. 100G} max.
Malfunction: 300 m/s
2
{approx.30G} max.
Durability (see note 4) Mechanical: 1,000,000 operations min.
(60 operations/min.)
Electrical: 50,000 operations min.
(20 operations/min.)
Mechanical: 1,000,000 operations min.
(60 operations/min.)
Electrical: 200,000 operations min.
(20 operations/min)
Degree of protection IEC IP67 (see note 5)
(excluding the terminals on terminal models)
Degree of protection against electric shock Class 1
Proof tracking index (PTI) 175
Ambient operating temperature
−20°Cto 70°C (at ambient humidity of 60% max.) (with no icing)
Ambient operating humidity 85% max. (for 5
°C to 35°C)
Weight Approx. 2 g (pin plunger models with terminals)
