231
D2SW-PD2SW-P
Precautions
■ Cautions
Degree of Protection
Do not use this product in water. Although this models satisfy the
test conditions for the standard given below, this test is to check
the ingress of water into the switch enclosure after submerging
the Switch in water for a given time. Satisfying this test condition
does not mean that the Switch can be used in water.
IEC 60529: 2001 Degrees of protection provided by enclosures
(IP Code)
Code: IP67 (The test to meet the standard checks for water intru-
sion after immersion for 30 minutes.)
Do not operate the Switch when it is exposed to water spray, or
when water drops adhere to the Switch surface, or during sudden
temperature changes, otherwise water may intrude into the inte-
rior of the Switch due to a suction effect.
Prevent the Switch from coming into contact with oil and chemi-
cals. Otherwise, damage to or deterioration of Switch materials
may result.
Do not use the Switch in areas where it is exposed to silicon
adhesives, oil, or grease, otherwise faulty contact may result due
to the generation of silicon oxide.
The environment-resistant performance of the switch differs
depending on operating loads, ambient atmospheres, and instal-
lation conditions, etc. Please perform an operating test of the
switch in advance under actual usage conditions.
Connecting to Terminals
Connecting to Solder Terminals
When soldering the lead wire to the terminal, first insert the lead
wire conductor through the terminal hole and the conduct solder-
ing.
Make sure that the temperature at the tip of the soldering iron is
350 to 400
°C. Do not take more than 3 seconds to solder the
switch terminal, and do not impose external force on the terminal
for 1 min after soldering. Improper soldering involving an exces-
sively high temperature or excessive soldering time may deterio-
rate the characteristics of the Switch.
Connecting to Quick-connect Terminals
Wire the quick-connect terminals (#110) with receptacles. Insert
the terminals straight into the receptacles. Do not impose exces-
sive force on the terminal in the horizontal direction, otherwise the
terminal may be deformed or the housing may be damaged.
Connecting to PCB Terminal Boards
When using automatic soldering baths, we recommend soldering
at 260
±5°C within 5 seconds. Make sure that the liquid surface of
the solder does not flow over the edge of the board.
When soldering by hand, as a guideline, solder with a soldering
iron with a tip temperature of 350 to 400
°C within 3 seconds, and
do not apply any external force for at least 1 minutes after solder-
ing. When applying solder, keep the solder away from the case of
the Switch and do not allow solder or flux to enter the case.
Side-actuated (Cam/Dog) Operation
When using a cam or dog to operate the Switch, factors such as
the operating speed, operating frequency, push-button indenta-
tion, and material and shape of the cam or dog will affect the
durability of the Switch. Confirm performance specifications under
actual operation conditions before using the Switch in applica-
tions.
0.5
6.4±
0.2
A
3.2
2.15
8.55
9.5±
0.1
2.5±
0.07
dia.
19.8±
0.2
5.15
15.5
Three, 1.6 dia. holes
2.35
+0.075
-0.05
2.35
dia.
+0.075
-0.05
7.3
t=0.3 Stainless-steel lever
14.5±
0.6
3.3±
0.1
FP
OP
7.7
6.9
dia. 4.8 x 3.2
Polyacetal resin roller
Model D2SW-P2L2@@ D2SW-P01L2@@
OF max.
RF min.
0.6 N {61 gf}
0.05 N {5 gf}
OT min.
MD max.
0.8 mm
0.8 mm
FP max.
OP
19.3 mm
14.5
±0.8 mm
Model D2SW-P2L3@@ D2SW-P01L3@@
OF max.
RF min.
0.6 N {61 gf}
0.05 N {5 gf}
OT min.
MD max.
0.8 mm
0.8 mm
FP max.
OP
15.5 mm
10.7
±0.8 mm
Hinge Roller Lever Models
D2SW-P2L2@@
D2SW-P01L2@@
Simulated Roller Lever Models
D2SW-P2L3@@
D2SW-P01L3@@
0.5
6.4±
0.2
A
3.2
2.15
8.55
9.5±
0.1
2.5±
0.07
dia.
19.8±
0.2
5.15
15.5
Three, 1.6 dia. holes
2.35
+0.075
−0.05
2.35
dia.
R1.3
+0.075
−0.05
7.3
t=0.3 Stainless-steel lever
15.8±
0.6
3.3±
0.1
FP
OP
7.7
6.9
