EVAL-ADG5462FEBZ

UG-908 EVAL-ADG5462FEBZ User Guide
Rev. 0 | Page 10 of 12
13822-009
Figure 9. EVAL-ADG5462FEBZ Layer 3
13822-010
Figure 10. EVAL-ADG5462FEBZ Bottom Layer
EVAL-ADG5462FEBZ User Guide UG-908
Rev. 0 | Page 11 of 12
ORDERING INFORMATION
BILL OF MATERIALS
Table 2.
Reference Designator Description Manufacturer Part No. Stock Code
C1 to C3, C6, C9, C13 to C15 50 V, X7R, 0.1 µF multilayer ceramic capacitors, 0603 GRM188R71H104KA93D FEC 882-0023
C4, C5, C11, C12 50 V, 10 µF tantalum capacitors, D size TAJD106K050RNJ FEC 143-2387
C7, C8 4.7 µF ceramic multilayer capacitors C2012X5R1H475K125AB FEC 2346932
D1 to D4, S1 to S4 50 Ω SMB sockets Not applicable Do not insert
DR, FF 50 straight SMB jacks SMB1251B1-3GT30G-50 FEC 1111349
GND1, GND2 Black test points 20-2137 FEC 873-1128
J1 to J3 4-pin terminal blocks (5 mm pitch) CTB5000/4 FEC 151791
J4 2-pin terminal block (5 mm pitch) CTB5000/2 FEC 151789
LED1 LED, SMD green, 0805 KP-2012SGC FEC 1318243
LED2
LED, SMD red, 0805
KP-2012SRC-PRV
FEC 1318244
Q1, Q2 Transistors, N-MOSFET, 60 V, 0.23 A, SOT-23 BSS138N FEC 115-6434
R1 to R3, R7 to R9, R13, R16,
R19, R23, R31, R37, R43
Resistors, 0603, 1%, 0 Ω MC0063W06030R FEC 9331662
R4 to R6, R10 to R12, R17, R22,
R24 to R30, R32, R33, R38
SMD resistors, 0603 Not applicable Do not insert
R14, R36 Resistors, 300 Ω, 0.1 W, 1%, 0805 MC01W08051300R FEC 9332987
R15 Resistor, 1 kΩ, 0.063 W, 1%, 0603 MC0063W060311K FEC 9330380
R18, R20, R35, R39 Resistors, 0805, 1%, 0 Ω MC01W08050R FEC 9333681
R21, R34, R40 to R42 SMD resistors, 0805 Not applicable Do not insert
SW1 SPDT, SMT slide switch Digi-Key CAS-120TA CAS120JCT-ND
T1 to T8, T_DR, T_FF Red test points 20-313137 FEC 873-1144
U1 User defined fault protection and detection,
10 Ω R
ON
, quad channel protector
ADG5462F ADG5462FBRUZ
U2 40 V, 200 mA, low noise, CMOS LDO linear regulator ADP7142AUJZ-5.0 ADP7142AUJZ-5.0-R7
UG-908 EVAL-ADG5462FEBZ User Guide
Rev. 0 | Page 12 of 12
NOTES
ESD Caution
ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection
circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.
Legal Terms and Conditions
By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the Evaluation Board”), you are agreeing to be bound by the terms and conditions
set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation Board until you
have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”) and Analog Devices, Inc.
(“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to Customer a free, limited, personal,
temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and agrees that the Evaluation Board is provided
for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted is expressly made subject to the following additional
limitations: Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board; and (ii) permit any Third Party to access the Evaluation Board. As used herein, the term
Third Party” includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is NOT sold to Customer; all rights not expressly granted herein, including
ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all be considered the confidential and proprietary information of ADI. Customer may
not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of use of the Evaluation Board or termination of this Agreement, Customer agrees to
promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any
occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited to soldering or any other activity that affects the material content of the Evaluation Board.
Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice
to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED AS IS” AND ADI MAKES NO
WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED
TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL
PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF
THE EVALUATION BOARD, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE
AMOUNT OF ONE HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable
United States federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and constr
ued in accordance with the substantive laws of the Commonwealth of
Massachusetts (excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby
submits to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.
©2015 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
UG13822-0-11/15(0)

EVAL-ADG5462FEBZ

Mfr. #:
Manufacturer:
Analog Devices Inc.
Description:
Switch IC Development Tools EVALUATION BOARD
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet