ISL43240
4
FN6036.3
December 15, 2014
Submit Document Feedback
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full 2-6V
Positive Supply Current, I+ V
S
= 5.5V, V
IN
= 0V or V+, Switch On or Off 25 -1 0.01 1 µA
Full -1 - 1 µA
Negative Supply Current, I- 25 -1 0.01 1 µA
Full -1 - 1 µA
NOTES:
8. V
IN
= Input voltage to perform proper function.
9. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
10. Leakage parameter is 100% tested at high temp, and guaranteed by correlation at +25°C.
11. Flatness is defined as the delta between the maximum and minimum r
ON
values over the specified voltage range.
12. Between any two switches.
Electrical Specifications 5V Supply Test Conditions: V+ = +4.5V to +5.5V, V- = GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 7),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Note 8
)TYP
MAX
(Note 8)UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON-resistance, r
ON
V+ = 4.5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3.5V,
See Figure 5
25 - 30 40 Ω
Full - - 50 Ω
r
ON
Matching Between Channels,
r
ON
V+ = 4.5V, I
COM
= 1.0mA, V
NO
or V
NC
= 3V 25 - 0.5 3 Ω
Full - - 4 Ω
r
ON
Flatness, R
FLAT(ON)
V+ = 5.5V, I
COM
= 1.0mA, V
NO
or V
NC
= 1V, 2V, 3V,
Note 10
25 - 4.4 6 Ω
Full - - 8 Ω
NO or NC OFF Leakage Current,
I
NO(OFF)
or I
NC(OFF)
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 4.5V, 1V, Note 9 25 -0.2 - 0.2 nA
Full -2.5 - 2.5 nA
COM ON Leakage Current, I
COM(ON)
V+ = 5.5V, V
COM
= 1V, 4.5V, V
NO
or V
NC
= 1V, 4.5V Note 9 25 -0.4 - 0.4 nA
Full -5 - 5 nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage High, V
INH
Full 2.4 1.5 - V
Input Voltage Low, V
INL
Full - 1.4 0.8 V
Input Current, I
INH
, I
INL
V+ = 5.5V, V
IN
= 0V or V+ Full -1 - 1 µA
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 4.5V, V
NO
or V
NC
= 3V, R
L
= 300Ω, C
L
= 35pF,
V
IN
= 0 to 3V, See Figure 1
25 - 64 80 ns
Full - - 90 ns
Turn-OFF Time, t
OFF
V+ = 4.5V, V
NO
or V
NC
= 3V, R
L
= 300Ω, C
L
= 35pF,
V
IN
= 0 to 3V, See Figure 1
25 - 29 40 ns
Full - - 45 ns
Break-before-make Time Delay, t
D
V+ = 5.5V, V
NO
or V
NC
= 3V, R
L
= 300Ω, C
L
= 35pF,
V
IN
= 0 to 3V, See Figure 3
Full 15 39 - ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0ΩSee Figure 2 25 - 1.2 2 pC
NO OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 7 25 - 10 - pF
NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 7 25 - 10 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, See Figure 7 25 - 30 - pF
OFF Isolation R
L
= 50Ω, C
L
= 15pF, f = 1MHz,
V
NO
or V
NC
= 1V
RMS
, See Figures 4 and 6
25 - 71 - dB
Crosstalk, Note 11
25 - -92 - dB
Power Supply Rejection Ratio R
L
= 50Ω, C
L
= 5pF, f = 1MHz 25 - 59 - dB
Electrical Specifications ±5V Supply Test Conditions: V
SUPPLY
= 4.5V to 5.5V, GND = 0V, V
INH
= 2.4V, V
INL
= 0.8V (Note 7),
Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
MIN
(Note 8
)TYP
MAX
(Note 8)UNITS
