MAX97200AEVKIT+

_______________________________________________________________ Maxim Integrated Products 1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX97200A Evaluation Kit
Evaluates: MAX97200A/MAX97200B
General Description
The MAX97200A evaluation kit (EV kit) is a fully
assembled and tested circuit board that evaluates the
MAX97200A. The MAX97200A is a 20mW Class G head-
phone amplifier that employs Maxim’s second-generation
DirectDrive
M
technology.
The MAX97200A EV kit provides 3dB gain, is powered
from a 1.8V single power supply, and includes a shut-
down input. The MAX97200A EV kit also evaluates the
MAX97200B. Request a free MAX97200B IC sample
from the factory when ordering the MAX97200B EV kit.
Features
S 1.8V Single-Supply Operation
S 20mW Class G Headphone Amplifier
S 3dB Gain
S Low-Quiescent Current, 1.15mA at PVIN = 1.8V
S Low-Power Shutdown Input
S Evaluates the MAX97200B (with IC Replacement)
S Fully Assembled and Tested
Ordering Information
Component List
Component Suppliers
19-5156; Rev 0; 2/10
DirectDrive is a registered trademark of Maxim Integrated
Products, Inc.
Note: Indicate that you are using the MAX97200A when contacting these component suppliers.
+Denotes lead(Pb)-free and RoHS compliant.
PART TYPE
MAX97200AEVKIT+ EV Kit
DESIGNATION QTY DESCRIPTION
C1 1
10FF Q20%, 6.3V X5R
ceramic capacitor (0603)
Murata GRM188R60J106M
TDK C1608X5R0J106M
C2 1
0.1FF Q10%, 25V X7R
ceramic capacitor (0603)
Murata GRM188R71E104K
TDK C1608X7R1E104K
C3–C7 5
1FF Q10%, 10V X7R
ceramic capacitors (0603)
Murata GRM188R71C105K
TDK C1608X7R1C105K
DESIGNATION QTY DESCRIPTION
GND, OUTL,
OUTR, PVDD,
PVSS
5 Test points
J1 1 3.5mm stereo headphone jack
JU1 1 2-pin header
R1 1
10kI Q5% resistor (0603)
U1 1
Class G headphone amplifier
(12 WLP)
Maxim MAX97200AEWC+T
1 Shunt
1
PCB MAX97200A
EVALUATION KIT+
SUPPLIER PHONE WEBSITE
Murata Electronics North America, Inc. 770-436-1300 www.murata-northamerica.com
TDK Corp. 847-803-6100 www.component.tdk.com
MAX97200A Evaluation Kit
Evaluates: MAX97200A/MAX97200B
2 ______________________________________________________________________________________
Quick Start
Recommended Equipment
• 1.8VDCsupply
• Stereoaudiosignalsource
• Pairofstereoheadphones
Procedure
The MAX97200A EV kit is fully assembled and test-
ed. Follow the steps below to verify board operation.
Caution: Do not turn on the power supply until all
connections are completed.
1) Verify that shunts are installed as follows:
JU1: Installed (device enabled)
2) Set the power-supply output to 1.8V.
3) Disable the power-supply output.
4) Connect the power-supply ground to the GND pad
and the power-supply positive output to the VIN pad
on the EV kit.
5) Connect the headphones to the stereo headphone
jack (J1) provided on the EV kit.
6) Verify that the audio source output is disabled.
7) Connect the left channel of the stereo audio source
to INL.
8) Connect the right channel of the stereo audio
source to INR.
9) Connect the ground of the stereo audio source to
GND.
10) Enable the stereo audio source.
11) Enable the power-supply output.
12) Verify that the headphones are playing the audio
source signal.
Jumper Configuration
Headphone Amplifier Shutdown
Jumper JU1 enables or disables the headphone ampli-
fier. See Table 1 for jumper JU1 configuration.
Table 1. Shutdown Input (JU1)
SHUNT POSITION
SHDN PIN
AMPLIFIER
Installed* Connected to VIN Enabled
Not installed Connected to GND Disabled
*Default position.
MAX97200A Evaluation Kit
Evaluates: MAX97200A/MAX97200B
_______________________________________________________________________________________ 3
Figure 1. MAX97200A EV Kit Schematic

MAX97200AEVKIT+

Mfr. #:
Manufacturer:
Maxim Integrated
Description:
KIT EVALUATION FOR MAX97200
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet