LTM8058
3
8058fa
For more information www.linear.com/LTM8058
ELECTRICAL CHARACTERISTICS
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: V
IN
+ V
OUT1
is defined as the sum of:
(V
IN
– GND) + (V
OUT1
– V
OUT
–
)
Note 3: The LTM8058 isolation is tested at 3kV DC for one second.
Note 4: The LTM8058E is guaranteed to meet performance specifications
from 0°C to 125°C. Specifications over the –40°C to 125°C internal
temperature range are assured by design, characterization and correlation
with statistical process controls. LTM8058I is guaranteed to meet
The l denotes the specifications which apply over the full internal
operating temperature range, otherwise specifications are at T
A
= 25°C, RUN = 12V (Note 4).
PARAMETER CONDITIONS MIN TYP MAX UNITS
Minimum Input DC Voltage BIAS = V
IN
, RUN = 2V
BIAS Open, RUN = 2V
l
l
3.1
4.3
V
V
V
OUT1
DC Voltage R
ADJ1
= 12.4k
R
ADJ1
= 6.98k
R
ADJ1
= 3.16k
l
4.75
2.5
5
12
5.25
V
V
V
V
IN
Quiescent Current V
RUN
= 0V
Not Switching
850
1 µA
µA
V
OUT1
Line Regulation 6V ≤ V
IN
≤ 31V, I
OUT
= 0.15A, RUN = 2V 1.7 %
V
OUT1
Load Regulation 0.05A ≤ I
OUT
≤ 0.2A, RUN = 2V 1.5 %
V
OUT1
Ripple (RMS) I
OUT
= 0.1A, 1MHz BW 20 mV
Input Short-Circuit Current V
OUT1
Shorted 30 mA
RUN Pin Input Threshold RUN Pin Rising 1.18 1.24 1.30 V
RUN Pin Current V
RUN
= 1V
V
RUN
= 1.3V
2.5
0.1
µA
µA
SS Threshold 0.7 V
SS Sourcing Current SS = 0V –10 µA
BIAS Current V
IN
= 12V, BIAS = 5V, I
LOAD1
= 100mA 8 mA
Minimum BIAS Voltage (Note 5) I
LOAD1
= 100mA 3.1 V
LDO (V
OUT2
) Minimum Input DC Voltage (Note 6) 1.8 2.3 V
V
OUT2
Voltage Range V
OUT1
= 16V, R
ADJ2
Open, No Load (Note 6)
V
OUT1
= 16V, R
ADJ2
= 41.2k, No Load (Note 6)
1.22
15.8
V
V
ADJ2 Pin Voltage V
OUT1
= 2V, I
OUT2
= 1mA (Note 6)
V
OUT1
= 2V, I
OUT2
= 1mA (Note 6)
l
1.19
1.22
1.25
V
V
V
OUT2
Line Regulation 2V < V
OUT1
< 16V, I
OUT2
= 1mA (Note 6) 1 5 mV
V
OUT2
Load Regulation V
OUT1
= 5V, 10mA ≤ I
OUT2
≤ 300mA (Note 6) 2 10 mV
LDO Dropout Voltage I
OUT2
= 10mA (Note 6)
I
OUT2
= 100mA (Note 6)
I
OUT2
= 300mA (Note 6)
0.25
0.34
0.43
V
V
V
V
OUT2
Ripple (RMS) C
BYP
= 0.01µF, I
OUT2
= 300mA, BW = 100Hz to 100kHz (Note 6) 20 µV
RMS
specifications over the full –40°C to 125°C internal operating temperature
range. The LTM8058MP is guaranteed to meet specifications over the
full –55°C to 125°C internal operating temperature range. Note that
the maximum internal temperature is determined by specific operating
conditions in conjunction with board layout, the rated package thermal
resistance and other environmental factors.
Note 5: This is the BIAS pin voltage at which the internal circuitry is
powered through the BIAS pin and not the integrated regulator. See BIAS
Pin Considerations for details.
Note 6: V
RUN
= 0V (Flyback not running), but the V
OUT2
post regulator is
powered by applying a voltage to V
OUT1
.
