1
FN4640.5
HIP1011B
PCI Hot Plug Controller
The HIP1011B, the third product in the HIP1011 family, is an
electronic circuit breaker that monitors, reports and protects
circuits from excessive load currents. As a pin-for-pin drop-in
alternative offering similar functionality to the widely used
HIP1011, the HIP1011B is compatible with CompactPCI
peripheral boards and PCI Hot Plug systems where voltage
“health” monitoring and reporting are centralized by the
system controller IC. The HIP1011B does not monitor nor
respond to under voltage conditions thus making control of a
wide range of voltages possible.
The HIP1011B creates a small and simple yet complete
power control solution to control the four independent
supplies (+5V, +3.3V, +12V, and -12V) found in PCI and
CompactPCI systems. For the +12V and -12V supplies,
overcurrent protection is provided internally with integrated
current sensing FET switches. For the +5V and +3.3V
supplies, overcurrent protection is provided by sensing the
voltage across the external current-sense resistors. The
PWRON input controls the state of both internal and external
switches. During an overcurrent condition on any output, all
MOSFETs are latched-off and a LOW (0V) is asserted on the
FLTN output. The FLTN latch is cleared when the PWRON
input is toggled low again. During initial power-up of the main
V
CC
supply (+12V), the PWRON input is inhibited from
turning on the switches, and the latch is held in the Reset
state until the V
CC
input is greater than 10V.
User programmability of the overcurrent threshold, response
time and turn-on slew rate is provided. A resistor connected
to the OCSET pin programs the overcurrent thresholds. A
capacitor may be added to the FLTN pin to adjust the fault
reporting and power-supply latch-off response times after an
over-current event. Capacitors connected to the gate pins
determine the turn-on rate.
Features
• Allows for System Centralized Voltage Monitoring
• Adjustable Delay to Fault Notification and Latch-Off
• Controls Four Supplies: +5V, +3.3V, +12V, and -12V
• Internal MOSFET Switches for +12V and -12V Outputs
• P Interface for On/Off Control and Fault Reporting
• Adjustable Overcurrent Protection for All Supplies
• Provides Overcurrent Fault Isolation
• Adjustable Turn-On Slew Rate
• Minimum Parts Count Solution
• No Charge Pump
• Pb-Free Available (RoHS Compliant)
Applications
• PCI Hot Plug
•
CompactPCI
Pinout
HIP1011B
(SOIC)
TOP VIEW
Ordering Information
PART NUMBER
TEMP. RANGE
(
o
C) PACKAGE
PKG.
DWG. #
HIP1011BCB 0 to 70 16 Ld SOIC M16.15
HIP1011BCB-T 0 to 70 Tape and Reel
HIP1011BCBZA
(See Note)
0 to 70 16 Ld SOIC
(Pb-free)
M16.15
HIP1011BCBZA-T
(See Note)
0 to 70 Tape and Reel (Pb-free)
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with
both SnPb and Pb-free soldering operations. Intersil Pb-free products
are MSL classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J STD-020C.
9
10
11
12
13
14
16
15
8
7
6
5
4
3
2
1
M12VIN
FLTN
3V5VG
V
CC
12VIN
3VISEN
OCSET
3VS
M12VO
12VG
GND
12VO
M12VG
5VISEN
5VS
PWRON
Data Sheet November 18, 2004
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
| Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003, 2004. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
N
O
T
R
E
CO
M
M
E
N
DE
D
F
O
R
NE
W
DE
S
I
G
NS
N
O
R
E
C
O
M
M
E
ND
E
D
R
E
P
L
AC
E
M
E
N
T
c
o
n
t
a
c
t
o
u
r
T
e
c
h
n
i
c
a
l
S
u
p
p
o
r
t
C
e
n
t
e
r
a
t
1
-
8
8
8
-
I
N
T
E
R
S
I
L
o
r
w
w
w
.
i
n
t
e
r
s
i
l
.c
o
m
/
t
s
c
