OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

STK672-732AN-E

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P26
© Semiconductor Components Industries, LLC, 2016 1 Publication Order Number :
October 2016 - Rev. 1 STK672-732AN-E/D
www.onsemi.com
ORDERING INFORMATION
See detailed ordering and shipping information on page 26 of this data sheet.
STK672-732AN-E
Stepper Motor Driver IPM
(Intelligent Power Module)
Unipolar 2-Phase
Overview
The STK672-732AN-E is a IPM for use as a unipolar,
2-phase stepper
motor driver with PWM current control.
Applications
Office photocopiers, printers, etc.
Features
Built-in overcurrent detection function, overheat detection function (output
current OFF).
FAULT signal (active low) is output when overcurrent or overheat is detected.
Built-in power on reset function.
Phase signal input driver activated with an active Low and incorpororates a
simulataneous ON prevention function.
Supports schmitt input for 2.5 V high level input.
Incorporating a current detection resistor (0.141 Ω : resistor tolerance 2%),
motor current can be set using two external resistors.
The ENABLE pin can be used to cut output current while maintaining the
excitation mode.
Supports compatible pins with STK672-740AN-E.
Specifications
Absolute Maximum Ratings
at Tc = 25C
Parameter Symbol Conditions Ratings Unit
Maximum supply voltage 1 V
CC
max No signal
52
V
Maximum supply voltage 2 V
DD
max No signal
0.3 to 6.0
V
Input voltage Vin max Logic input pins
0.3 to 6.0
V
Output current 1 IOP max 10 μs 1 pulse (resistance load)
10
A
Output current 2 IOH max V
DD
= 5 V, More than 200 Hz
2.65
A
Output current 3 IOF max 16pin Output current
10
mA
Allowable power dissipation 1 PdMF max With an arbitrarily large heat sink. Per MOSFET
7.3
W
Allowable power dissipation 2 PdPK max No heat sink
2.8
W
Operating substrate
temperature
Tcmax
105
°C
Junction temperature Tjmax
150
°C
Storage temperature Tstg
40 to 125
°C
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality should not be assumed,
damage may occur and reliability may be affected.
STK672-732AN-E
www.onsemi.com
2
Allowable Operating Ranges at Tc = 25C
Parameter Symbol Conditions Ratings unit
Operating supply voltage 1 V
CC
With signals applied 0 to 42 V
Operating supply voltage 2 V
DD
With signals applied 5 5% V
Input high voltage V
IH
Pins 10, 12, 13, 14, 15, 17,
V
DD
= 5 5%
2.5 to V
DD
V
Input low voltage V
IL
Pins 10, 12, 13, 14, 15, 17,
V
DD
= 5 5%
0 to 0.8 V
Output current 1 I
OH
1
Tc = 105C, More than 200 Hz,
Continuous operation, duty = 100%
2.0 A
Output current 2 I
OH
2
Tc = 80C, More than 200 Hz,
Continuous operation, duty = 100%,
See the motor current (I
OH
) derating
curve
2.2 A
Recommended operating
substrate temperature
Tc No condensation 0 to 105 C
Recommended Vref range Vref Tc = 105C 0.14 to 1.38 V
Electrical Characteristics
at Tc = 25C, V
CC
= 24 V, V
DD
= 5.0 V *1
Parameter Symbol Conditions min typ max unit
V
DD
supply current I
CCO
V
DD
= 5.0 V, ENABLE = Low 4.4 8.0 mA
Output average current *2 Ioave R/L = 1 / 0.62 mH in each phase 0.273 0.329 0.385 A
FET diode forward voltage
Vdf If = 1 A (R
L
= 23 ) 0.92 1.6 V
Output saturation voltage Vsat R
L
= 23 0.33 0.48 V
Control
Input pin
Input high voltage V
IH
Pins 10, 12, 13, 14, 15, 17 2.5 V
DD
V
Input low voltage V
IL
Pins 10, 12, 13, 14, 15, 17 0.3 0.8 V
5 V level input current
I
ILH
Pins 10, 12, 13, 14, 15, 17 = 5 V
50 75 A
GND level input current
I
ILL
Pins 10, 12, 13, 14, 15, 17 = GND
10 A
FAULT
pin
Output low voltage V
OLF
Pin 16 (I
O
= 5 mA) 0.25 0.5 V
5 V level leakage current
I
ILF
Pin 16 = 5 V
10 A
Vref input bias current I
IB
Pin 19 = 1.0 V 10 15 A
PWM frequency Fc 29 45 61 kHz
Overheat detection temperature TSD Design guarantee 144 C
Drain-source cut-off current I
DSS
V
DS
= 100 V, Pins 2, 6, 9, 18 = GND 1 A
Notes
*1: A fixed-voltage power supply must be used.
*2: The value for Ioave assumes that the lead frame of the product is soldered to the mounting circuit board.
Functional operation above the stresses listed in the Recommended Operating Ranges is not implied. Extended exposure to stresses beyond the Recommended
Operating Ranges limits may affect device reliability.
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product performance may not be
indicated by the Electrical Characteristics if operated under different conditions.
STK672-732AN-E
www.onsemi.com
3
0
0.5
1
1.5
2
2.5
3
0 102030405060708090100110
MOter Current IOH A
Operation substrate temperature Tc °C
200Hz 2ex
Hold
Notes
The current range given above represents conditions when output voltage is not in the avalanche state.
If the output voltage is in the avalanche state, see the allowable avalanche energy for STK672-7** series IPMs given in
a separate document.
The operating substrate temperature, Tc, given above is measured while the motor is operating.
Because Tc varies depending on the ambient temperature, Ta, the value of I
OH
, and the continuous or intermittent
operation of I
OH
, always verify this value using an actual set.
The Tc temperature should be checked in the center of the metal surface of the product package.
Derating Curve of Motor Current, I
OH,
vs. STK672-732AN-E Operating Substrate Temperature, Tc
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P26

STK672-732AN-E

Mfr. #:
Buy STK672-732AN-E
Manufacturer:
ON Semiconductor
Description:
Motor / Motion / Ignition Controllers & Drivers STEPPING MOTOR DRIVER
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet