OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

MKP1848S61550JP4C

P1-P3P4-P6P7-P9P10-P12P13-P15
MKP1848S DC-Link
www.vishay.com
Vishay Roederstein
Revision: 19-Mar-13
10
Document Number: 26010
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
APPLICATION NOTES AND LIMITING CONDITIONS
These capacitors are not suitable for mains applications as across-the-line capacitors without additional protection. These
mains applications are strictly regulated in safety standards and therefore electromagnetic interference suppression capacitors
conforming the standards must be used.
To select the capacitor for a certain application, the following conditions must be checked:
1. The continuous peak voltage (U
p+
) shall not exceed the DC voltage rating (U
NDC
)
2. The peak-to-peak ripple voltage (U
pp
) shall not be greater than 0.2 x U
NDC
3. For capacitors connected in parallel, normally the proof voltage and possibly the rated voltage must be reduced. For
information depending of the capacitance value and the number of parallel connections contact dc-film@vishay.com
.
4. The voltage peak slope (dU/dt) shall not exceed the pulse slope at the DC voltage rating.
If the pulse voltage is lower than the rated DC voltage, the rated voltage pulse slope may be multiplied by U
NDC
and divided
by the applied voltage.
For all other pulses following equation must be fulfilled:
T is the pulse duration
Note
• The capacitor unit may be subjected to the following surge without any significant reduction of lifetime expectancy
MAXIMUM REPETITIVE PEAK VOLTAGES
REPETITIVE SURGE VOLTAGE MAXIMUM DURATION PER DAY
1.1 x U
NDC
30 % of on load duration
1.15 x U
NDC
30 min
1.2 x U
NDC
5 min
1.3 x U
NDC
1 min
1.5 x U
NDC
110 ms
U
p+
U
p-
t
Non reversing recurrent waveform
Voltage (V)
U
NDC
2 x
dU
dt
-------


2
x dt < U
NDC
x
dU
dt
-------


rated
0
T
MKP1848S DC-Link
www.vishay.com
Vishay Roederstein
Revision: 19-Mar-13
11
Document Number: 26010
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS
ROUTINE TEST - FINAL INSPECTION
5.14.2-1
External inspection, visual examination Legible marking as specified
5.14.2-2
Dimensions See specification drawing
5.3-1
Capacitance 1 kHz at room temperature See specific reference data
5.3-2
tan 1 kHz at room temperature
10 kHz at room temperature
See specific reference data
5.5.1-2
Voltage test between terminals 1.5 x U
NDC
at T
amb
Duration: 10 s
No visible damage or puncture
No flashover
5.7
Insulation resistance U
NDC
500 V measuring voltage 100 V at
room temperature
U
NDC
> 500 V measuring voltage 500 V at
room temperature
Duration: 1 min
See specific reference data
TYPE TESTS
5.14.2
External inspection Check for finish, marking and overall
dimensions
Legible marking and finish as specified
Dimensions: See specification drawing
5.14.0
Initial measurements Capacitance at 1 kHz
tan at 10 kHz
5.14.1-1/4
Robustness of terminations
IEC 60068-2-21
Tensile Ua1
Wire diameter Section modulus Load
0.8 mm 0.5 mm
2
10 N
1.25 mm 1.2 mm
2
20 N
Duration: 10 s ± 1 s
Bending, Ub method 1
Wire diameter Section modulus Load
0.8 mm 0.5 mm
2
10 N
1.25 mm 1.2 mm
2
20 N
4 x 90°, duration: 2 s to 3 s/bend
5.14.1-6
Resistance to soldering heat
IEC 60068-2-20
No pre-drying, method 1A
Solder bath: 260 °C ± 5 °C
Duration: 10 s ± 1 s
5.14.4
Final measurements Capacitance
tan
|C/C| 0.5 %
Increase of tan 0.0050
compared to the values measured in 5.14.0
5.14.0
Initial measurements Capacitance at 1 kHz
tan at 10 kHz
5.14.3-1
Vibration
IEC 60068-2-6
10 Hz to 55 Hz; amplitude ± 0.35 mm or
acceleration 98 m/s
2
Test duration: 10 frequency cycles
3 axes offset from each other by 90°
1 octave/min
Visual examination No visible damage
MKP1848S DC-Link
www.vishay.com
Vishay Roederstein
Revision: 19-Mar-13
12
Document Number: 26010
For technical questions, contact: dc-film@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
5.14.3-2
Shock or impact
IEC 60068-2-6
Pulse shape: half sine
Acceleration: 490 m/s2
Duration of pulse: 11 ms
Visual examination No visible damage
5.14.4
Final measurements Capacitance
tan
|C/C| 0.5 %
Increase of tan 0.0050
compared to the values measured in 5.14.0
5.5.3-1
Initial measurements Capacitance at 1 kHz
tan at 10 kHz
R insulation
5.5.3-2
Voltage test between terminals 1.5 x U
NDC
at T
amb
Duration: 60 s
5.5.3-3
Final measurements Capacitance
tan
R insulation
|C/C| 0.5 %
Increase of tan 0.0050
R insulation 50 % of specified values
5.9-1
Initial measurements Capacitance at 1 kHz
tan at 10 kHz
5.9-2
Surge discharge test 1.1 x U
NDC
Number of discharges: 5
Time lapse: every 2 min (10 min total)
5.9-2
Voltage test between terminals Within 5 min after the surge
discharge test
Duration: 60 s
1.5 x U
NDC
at T
amb
5.9-3
Final measurements Capacitance
tan at 10 kHz
|C/C| 1.0 %
tan 1.2 x initial tan + 0.0001
compared to the values measured in 5.9-1
5.11-1
Initial measurements Capacitance at 1 kHz
tan at 10 kHz
5.11-2
Self healing test 1.5 x U
NDC
Duration: 10 s
Number of clearings 5
Clearing = Voltage drop of 5 %
increase the voltage at 100 V/s till
5 clearings occur
with a max. of 2.5 x U
NDC
for a duration of 10 s
5.11-3
Final measurements Capacitance
tan
|C/C| 0.5 %
tan 1.2 x initial tan + 0.0001
compared to the values measured in 5.11-1
INSPECTION REQUIREMENTS
SUB-CLAUSE NUMBER AND TEST CONDITIONS PERFORMANCE REQUIREMENTS
P1-P3P4-P6P7-P9P10-P12P13-P15

MKP1848S61550JP4C

Mfr. #:
Buy MKP1848S61550JP4C
Manufacturer:
Description:
Film Capacitors MKP, 500Vdc, 15 F, 37,5pitch, P2= 10,2mmP2, 4pins
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet