OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ADUM4150BRIZ

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P22
ADuM4150 Data Sheet
Rev. B | Page 12 of 21
DIN V VDE V 0884-10 (VDE V 0884-10):2006-12 INSULATION CHARACTERISTICS
This isolator is suitable for reinforced electrical isolation only within the safety limit data. Maintenance of the safety data is ensured by
protective circuits. The asterisk (*) marked on packages denotes DIN V VDE V 0884-10 approval.
Table 13.
Description Test Conditions/Comments Symbol Characteristic Unit
Installation Classification per DIN VDE 0110
For Rated Mains Voltage ≤ 150 V rms I to IV
For Rated Mains Voltage ≤ 300 V rms I to III
For Rated Mains Voltage ≤ 400 V rms I to II
Climatic Classification 40/105/21
Pollution Degree per DIN VDE 0110, Table 1 2
Maximum Working Insulation Voltage V
IORM
849 V peak
Input-to-Output Test Voltage, Method b1 V
IORM
× 1.875 = V
pd(m)
, 100% production test,
t
ini
= t
m
= 1 sec, partial discharge < 5 pC
V
pd(m)
1592 V peak
Input-to-Output Test Voltage, Method a
After Environmental Tests Subgroup 1 V
IORM
× 1.5 = V
pd(m)
, t
ini
= 60 sec, t
m
= 10 sec,
partial discharge < 5 pC
V
pd(m)
1274 V peak
After Input and/or Safety Test Subgroup 2
and Subgroup 3
V
IORM
× 1.2 = V
pd(m)
, t
ini
= 60 sec, t
m
= 10 sec,
partial discharge < 5 pC
V
pd(m)
1019 V peak
Highest Allowable Overvoltage V
IOTM
6000 V peak
Surge Isolation Voltage V
IOSM(TEST)
= 10 kV, 1.2 µs rise time, 50 µs, 50% fall time V
IOSM
6250 V peak
Safety Limiting Values Maximum value allowed in the event of a failure
(see Figure 2)
Case Temperature T
S
150 °C
Safety Total Dissipated Power P
S
2.4 W
Insulation Resistance at T
S
V
IO
= 500 V R
S
>10
9
Ω
Figure 2. Thermal Derating Curve, Dependence of Safety Limiting Values
with Case Temperature per DIN V VDE V 0884-10
RECOMMENDED OPERATING CONDITIONS
Table 14.
Parameter Symbol Value
Operating Temperature Range T
A
−40°C to +125°C
Supply Voltage Range
1
V
DD1
, V
DD2
3.0 V to 5.5 V
Input Signal Rise/Fall Times
1.0 ms
1
See the DC Correctness and Magnetic Field Immunity section for information
on the immunity to external magnetic fields.
3.0
2.5
2.0
1.5
1.0
0.5
0
0 50 100 150
SAFE LIMITING POWER (W)
AMBIENT TEMPERATURE (°C)
12371-002
Data Sheet ADuM4150
Rev. B | Page 13 of 21
ABSOLUTE MAXIMUM RATINGS
T
A
= 25°C, unless otherwise noted.
Table 15.
Parameter Rating
1
Storage Temperature (T
ST
) Range −65°C to +150°C
Ambient Operating Temperature
(T
A
) Range
−40°C to +125°C
Supply Voltages (V
DD1
, V
DD2
) −0.5 V to +7.0 V
Input Voltages (V
IA
, V
IB
, MCLK, MO,
SO,
MSS
)
−0.5 V to V
DDx
+ 0.5 V
Output Voltages (SCLK, DCLK,
SSS
,
MI, SI, V
OA
, V
OB
)
−0.5 V to V
DDx
+ 0.5 V
Average Output Current per Pin
2
−10 mA to +10 mA
Common-Mode Transients
3
−100 kV/µs to +100 kV/µs
1
V
DDx
= V
DD1
or V
DD2
.
2
See Figure 2 for maximum safety rated current values across temperature.
3
Refers to common-mode transients across the insulation barrier. Common-
mode transients exceeding the absolute maximum ratings may cause
latch-up or permanent damage.
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
Table 16. Maximum Continuous Working Voltage
1
Parameter Value Constraint
60 Hz AC Voltage 400 V rms 20 year lifetime at 0.1%
failure rate, zero average
voltage
DC Voltage 1173 V peak Limited by the creepage
of the package,
Pollution Degree 2,
Material Group II
2, 3
1
See the Insulation Lifetime section for details.
2
Other pollution degree and material group requirements yield a different limit.
3
Some system level standards allow components to use the printed wiring
board (PWB) creepage values. The supported dc voltage may be higher for
those standards.
ESD CAUTION
ADuM4150 Data Sheet
Rev. B | Page 14 of 21
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 17. Pin Function Descriptions
Pin No. Mnemonic Direction Description
1 V
DD1
Power Input Power Supply for Isolator Side 1. A bypass capacitor from V
DD1
to GND
1
to local ground is required.
2,10 GND
1
Return Ground 1. Ground reference for Isolator Side 1.
3 MCLK
Clock SPI Clock from the Master Controller.
4 MO Input SPI Data from the Master to the Slave MO/SI Line.
5
MI
Output
SPI Data from Slave to the Master MI/SO Line.
6
MSS
Input Slave Select from the Master. This signal uses an active low logic. The slave select pin may require as
much as 10 ns setup time from the next clock or data edge, depending on speed grade.
7 V
IA
Input Low Speed Data Input A.
8 V
OB
Output Low Speed Data Output B.
9 DCLK Output Delayed Clock Output. This pin provides a delayed copy of the MCLK.
11,19
GND
2
Return
Ground 2. Ground reference for Isolator Side 2.
12 NIC None No Internal Connection. This pin is not internally connected and serves no function in the ADuM4150.
13 V
IB
Input Low Speed Data Input B.
14 V
OA
Output Low Speed Data Output A.
15
SSS
Output Slave Select to the Slave. This signal uses an active low logic.
16 SO Input SPI Data from the Slave to the Master MI/SO Line.
17 SI Output SPI Data from the Master to the Slave MO/SI Line.
18 SCLK Output SPI Clock from the Master Controller.
20 V
DD2
Power Input Power Supply for Isolator Side 2. A bypass capacitor from V
DD2
to GND
2
to local ground is required.
Table 18. Power-Off Default State Truth Table (Positive Logic)
1
V
DD1
State V
DD2
State Side 1 Outputs Side 2 Outputs
SSS
Notes
Unpowered Powered Z Z Z Outputs on an unpowered side are high impedance within
one diode drop of ground
Powered Unpowered Z Z Z Outputs on an unpowered side are high impedance within
one diode drop of ground
1
Z is high impedance.
V
DD1
1
GND
1
2
MCLK
3
MO
4
20
19
18
17
MI
5
MSS
6
V
IA
7
16
15
14
V
OB
8
13
DCLK
9
12
GND
1
V
DD2
GND
2
SCLK
SI
SO
SSS
V
OA
V
IB
NIC
GND
2
10
11
ADuM4150
TOP VIEW
(Not to Scale)
NOTES
1. NIC = NOT INTERNALLY CONNECTED. THIS PIN
IS NOT INTERNALLY CONNECTED AND SERVES
NO FUNCTION IN THE ADuM4150.
12371-003
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P22

ADUM4150BRIZ

Mfr. #:
Buy ADUM4150BRIZ
Manufacturer:
Analog Devices Inc.
Description:
Digital Isolators 6 Ch 40 MHz Iso lator for Interface
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet