ADL5590ACPZ-R7

ADL5590/ADL5591 Data Sheet
Rev. A | Page 4 of 8
Parameter Test Conditions/Comments Min Typ Max Unit
LO Leakage −44 dBc
Output Return Loss 5.4 dB
Output P1 dB 16 dBm
Output IP3 f1
BB
= 3.5 MHz, f2
BB
= 4.5 MHz, P
OUT
= −1 dBm per tone 30 dBm
Output IP2 f1
BB
= 3.5 MHz, f2
BB
= 4.5 MHz, P
OUT
= −1 dBm per tone 60 dBm
Output Noise Density P
OUT
= 5 dBm, 6 MHz carrier offset −156 dBc/Hz
Output Noise Floor Baseband inputs biased to 1.5 V −157 dBm/Hz
Modulation Spectrum Relative to carrier in 30 kHz, P
OUT
= 3 dBm, 8 PSK
250 kHz carrier offset −42.5 dBc
400 kHz carrier offset −71.3 dBc
600 kHz carrier offset −79.4 dBc
1.2 MHz carrier offset −80.2 dBc
RMS Error Vector Magnitude P
OUT
= 3 dBm, 8 PSK 0.5 %
Peak Error Vector Magnitude P
OUT
= 3 dBm, 8 PSK 1.7 %
ADL5591 @ f
RF
= 1960 MHz
Output Power V
IQ
= 1.0 V p-p differential 2.5 4.7 6.5 dBm
vs. Frequency f
RF
= 1930 MHz to 1990 MHz
0.1
dB
vs. Temperature 0°C to 85°C +0.011 dB/°C
−25°C to 0°C +0.011 dB/°C
Sideband Suppression −48 dBc
LO Leakage −44 dBc
Output Return Loss 6.0 dB
Output P1dB 16 dBm
Output IP3 f1
BB
= 3.5 MHz, f2
BB
= 4.5 MHz, P
OUT
= −1 dBm per tone 30 dBm
Output IP2 f1
BB
= 3.5 MHz, f2
BB
= 4.5 MHz, P
OUT
= −1 dBm per tone 60 dBm
Output Noise Density P
OUT
= 5 dBm, 6 MHz carrier offset −156 dBc/Hz
Output Noise Floor Baseband inputs biased to 1.5 V 157 dBm/Hz
Modulation Spectrum Relative to carrier in 30 kHz, P
OUT
= 3 dBm, 8 PSK
250 kHz carrier offset −42.5 dBc
400 kHz carrier offset −71.4 dBc
600 kHz carrier offset −79.7 dBc
1.2 MHz carrier offset −80.5 dBc
RMS Error Vector Magnitude P
OUT
= 3 dBm, 8 PSK 0.5 %
Peak Error Vector Magnitude P
OUT
= 3 dBm, 8 PSK 1.6 %
LO INPUTS LOIP, LOIN
LO Drive Level
1
−1 +2 +5 dBm
Input Return Loss ADL5590 @ f
RF
= 880 MHz 7.5 dB
ADL5591 @ f
RF
= 1850 MHz 10.7 dB
BASEBAND INPUTS Pins IBBP, IBBN, QBBP, QBBN
I and Q Input Bias Level 1.5 V
Bandwidth (3 dB) 250 MHz
Differential Input Impedance 9
POWER SUPPLIES Pin VPS1 to Pin VPS5
Voltage Full specification 4.75 5.25 V
Degraded specification 4.5 5.5 V
Supply Current
ADL5590 170 mA
ADL5591 170 mA
1
LO drive in excess of 5 dBm can be provided to further reduce noise at 6 MHz carrier offset.
Data Sheet ADL5590/ADL5591
Rev. A | Page 5 of 8
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter Rating
Supply Voltage, VPS1 to VPS5 5.5 V
IBBP, IBBN, QBBP, QBBN 0 V, 3 V
LOIP 10 dBm
Internal Power Dissipation 1155 mW
θ
JA
(Exposed Pad Soldered Down) 40°C/W
Maximum Junction Temperature 132°C
Operating Temperature Range −40°C to +85°C
Storage Temperature Range −65°C to +150°C
Maximum Soldering Temperature 260°C
Stresses at or above those listed under Absolute Maximum
Ratings may cause permanent damage to the product. This is a
stress rating only; functional operation of the product at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Operation beyond
the maximum operating conditions for extended periods may
affect product reliability.
ESD CAUTION
ADL5590/ADL5591 Data Sheet
Rev. A | Page 6 of 8
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
GND
QBBN
QBBP
VOUT
GND
IBBN
IBBP
GND
GND
GND
NOTES
1. EXPOSED PAD. CONNECT THE EXPOSED PAD TO
THE GROUND PLANE VIA A LOW IMPEDANCE PATH.
GND
VPS1
GND
LOIP
GND
LOIN
GND
GND
G
N
D
G
N
D
G
N
D
V
P
S
2
G
N
D
V
P
S
3
G
N
D
G
N
D
G
N
D
V
P
S
5
G
N
D
G
N
D
G
N
D
G
N
D
V
P
S
4
G
N
D
G
N
D
G
N
D
1
2
3
4
5
6
7
8
9
27
26
25
24
23
22
21
20
19
10
11
12
13
14
15
16
17
18
36
35
34
33
32
31
30
29
28
06661-002
ADL5590/
ADL5591
TOP VIEW
(Not to Scale)
Figure 2. Pin Configuration
Table 3. Pin Function Descriptions
Pin No. Mnemonic Description
1, 2, 5, 7 to 12, 14,
16 to 19, 22, 24,
27 to 30, 32, 34 to 36
GND Ground. Connect to ground plane via a low impedance path.
3, 13, 15, 31, 33
VPS1, VPS2, VPS3,
VPS4, VPS5
Positive Supply Voltage. Connect all pins to the same supply. To ensure adequate
external bypassing, connect 0.1 μF capacitors between each pin and ground.
4, 6 LOIP, LOIN
Local Oscillator Input. 50 Ω single-ended local oscillator input. Pins must be ac-coupled.
AC-couple LOIN to ground and drive LO through LOIP.
20, 21, 25, 26 IBBP, IBBN, QBBN, QBBP
Baseband Inputs. Differential in-phase and quadrature baseband inputs. These high
impedance inputs must be dc-biased to approximately 1.5 V dc. These inputs are not
self-biased and must be externally biased.
23 VOUT
RF Output. Single-ended, 50 Ω, internally biased RF output. Pin must be ac-coupled to
the load.
Exposed Pad Exposed Pad. Connect the exposed pad to the ground plane via a low impedance path.

ADL5590ACPZ-R7

Mfr. #:
Manufacturer:
Analog Devices Inc.
Description:
Modulator / Demodulator EMOD GSM ASIC FOR ERICSSON 1800-1990 MHZ
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet