Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
201654C • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice November 2, 2011 1
DATA SHEET
SE2600S: 2.4 GHz WLAN Switch/Low-Noise Amplifier
Front-End
Applications
IEEE802.11b DSSS WLAN
IEEE802.11g/n OFDM WLAN
Embedded systems
Features
Integrates an SP3T switch and LNA with bypass mode
Gain: 12 dB
Noise Figure: 1.8 dB
Bluetooth
®
path loss: 0.5 dB
Small WLCSP (11-bump, 1.07 x 1.05 x 0.38 mm) 250 μm ball
pitch package (MSL1, 260 °C per JEDEC-J-STD-020)
Figure 2. SE2600S Pinout – 11-Bump CSP
(Top View, Bumps Down)
Figure 1. SE2600S Block Diagram
Description
The SE2600S is an integrated Front-End Module (FEM) with a
Bluetooth port to complement WLAN chipsets with an integrated
Power Amplifier (PA).
The SE2600S integrates a Single-Pole, Triple-Throw (SP3T) switch
and Low-Noise Amplifier (LNA) with a bypass mode in an ultra-
compact package. The device is capable of switching between
WLAN receive, WLAN transmit, and Bluetooth.
The SE2600S is provided in a small, 11-bump, 1.07 x 1.05 mm
Wafer Level Chip Scale Package (WLCSP). A functional block
diagram is shown in Figure 1. The pin configuration and package
are shown in Figure 2. Signal pin assignments and functional pin
descriptions are provided in Table 1.
DATA SHEET • SE2600S WLAN SWITCH/LNA FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
2 November 2, 2011 • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice 201654C
Table 1. SE2600S Signal Descriptions
Pin # Name Description Pin # Name Description
1 TX WLAN transmit port 7 GND Ground
2 GND Ground 8 BT Bluetooth port
3 VON LNA control signal 9 VC1 BT switch control pin
4 RX WLAN receive port 10 RFC RF common port (antenna)
5 VDD Positive power supply voltage 11 VC3 Transmit switch control pin
6 VC2 Receive switch control pin
Table 2. SE2600S Absolute Maximum Ratings
Parameter Symbol Minimum Maximum Units
Supply voltage VDD 0 3.6 V
DC input on control pins 0.5 VDD + 0.5 V
Transmit input power, RFC terminated in 50 Ω match PIN +27 dBm
Operating temperature TA 40 +85 °C
Storage temperature TSTG 40 +150 °C
Note: Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other
parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device.
CAUTION: Although this device is designed to be as robust as possible, Electrostatic Discharge (ESD) can damage this device. This device
must be protected at all times from ESD. Static charges may easily produce potentials of several kilovolts on the human body
or equipment, which can discharge without detection. Industry-standard ESD precautions should be used at all times. The
SE2600S ESD threshold level is 1000 VDC using Human Body Model (HBM) testing.
Table 3. Recommended Operating Conditions
Parameter Symbol Minimum Typical Maximum Units
Supply voltage VDD 2.7 3.3 3.6 V
Control voltage (relative to GND = 0 V) VCTL 0 VDD V
Operating temperature TA 40 +25 +85 °C
Electrical and Mechanical Specifications
The absolute maximum ratings of the SE2600S are provided in
Table 2. The recommended operating conditions are specified in
Table 3 and electrical specifications are provided in Tables 4
through 7.
The state of the SE2600S is determined by the logic provided in
Table 8.
DATA SHEET • SE2600S WLAN SWITCH/LNA FEM
Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com
201654C • Skyworks Proprietary and Confidential Information • Products and Product Information are Subject to Change Without Notice November 2, 2011 3
Table 4. SE2600S Electrical Specifications: DC Characteristics (Note 1)
(V
DD = 3.3 V, TA = +25 °C, All Unused Ports Terminated With 50 Ω, Unless Otherwise Noted)
Parameter Symbol Test Condition Min Typical Max Units
LNA current IDD High gain mode
Bypass mode
10 13
60
mA
μA
LNA control current ICTL 20 μA
BT port control current IC1 20 μA
TX port control current IC3 20 μA
Control voltage:
High
Low
V
IH
V
IL
2.7
0
3.6
0.3
V
V
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Table 5. SE2600S Electrical Specifications: AC Characteristics, Transmit (RFC to TX Port) (Note 1)
(VC1 = VC2 = VON = 0 V, V
DD = 3.3 V, TA = +25 °C, All Unused Ports Terminated With 50 Ω, Unless Otherwise Noted)
Parameter Symbol Test Condition Min Typical Max Units
Frequency f 2.4 2.5 GHz
Insertion loss IL 0.5 0.7 dB
Input return loss S11 16 14 dB
Output return loss S22 16 14 dB
Switch isolation Iso VC3 = 0 V 23 dB
1 dB Input Compression Point IP1dB +31 dBm
Turn-on/turn-off time TON, TOFF 90/10% of final output
power level
400 ns
Note 1: Performance is guaranteed only under the conditions listed in this Table.
Table 6. SE2600S Electrical Specifications: AC Characteristics, Bluetooth (RFC to BT Port) (Note 1)
(VC2 = VC3 = VON = 0 V, V
DD = 3.3 V, TA = +25 °C, All Unused Ports Terminated With 50 Ω, Unless Otherwise Noted)
Parameter Symbol Test Condition Min Typical Max Units
Frequency f 2.4 2.5 GHz
Insertion loss IL 0.5 0.7 dB
Input return loss, BT port S11 16 14 dB
Output return loss, BT port S22 16 14 dB
Switch isolation Iso VC1 = 0 V 25 dB
1 dB Input Compression Point IP1dB +31 dBm
Turn-on/turn-off time TON, TOFF 90/10% of final output
power level
400 ns
Note 1: Performance is guaranteed only under the conditions listed in this Table.

SE2600S-R

Mfr. #:
Manufacturer:
Skyworks Solutions, Inc.
Description:
RF Front End 2.4GHz Gain 12 dB NF 1.8dB
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet