PRELIMINARY
CY7C1352G
Document #: 38-05514 Rev. *B Page 3 of 13
Pin Definitions
Name I/O Description
A0, A1, A Input-
Synchronous
Address Inputs used to select one of the 256K address locations. Sampled at the rising
edge of the CLK. A
[1:0]
are fed to the two-bit burst counter.
BW
[A:B]
Input-
Synchronous
Byte Write Inputs, active LOW. Qualified with
WE to conduct writes to the SRAM. Sampled
on the rising edge of CLK.
WE
Input-
Synchronous
Write Enable Input, active LOW. Sampled on the rising edge of CLK if CEN is active LOW.
This signal must be asserted LOW to initiate a write sequence.
ADV/LD
Input-
Synchronous
Advance/Load Input. Used to advance the on-chip address counter or load a new address.
When HIGH (and CEN
is asserted LOW) the internal burst counter is advanced. When LOW,
a new address can be loaded into the device for an access. After being deselected, ADV/LD
should be driven LOW in order to load a new address.
CLK Input-Clock Clock Input. Used to capture all synchronous inputs to the device. CLK is qualified with CEN.
CLK is only recognized if CEN
is active LOW.
CE
1
Input-
Synchronous
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE
2
and CE
3
to select/deselect the device.
CE
2
Input-
Synchronous
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in conjunction
with CE
1
and CE
3
to select/deselect the device.
CE
3
Input-
Synchronous
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in conjunction
with CE
1
and
CE
2
to select/deselect the device.
OE
Input-
Asynchronous
Output Enable, asynchronous input, active LOW. Combined with the synchronous logic
block inside the device to control the direction of the I/O pins. When LOW, the DQ pins are
allowed to behave as outputs. When deasserted HIGH, DQ pins are tri-stated, and act as input
data pins. OE
is masked during the data portion of a write sequence, during the first clock when
emerging from a deselected state, when the device has been deselected.
CEN
Input-
Synchronous
Clock Enable Input, active LOW. When asserted LOW the Clock signal is recognized by the
SRAM. When deasserted HIGH the Clock signal is masked. Since deasserting CEN
does not
deselect the device, CEN
can be used to extend the previous cycle when required.
ZZ Input-
Asynchronous
ZZ “sleep” Input. This active HIGH input places the device in a non-time-critical “sleep”
condition with data integrity preserved. For normal operation, this pin has to be LOW or left
floating. ZZ pin has an internal pull-down.
DQs I/O-
Synchronous
Bidirectional Data I/O Lines. As inputs, they feed into an on-chip data register that is triggered
by the rising edge of CLK. As outputs, they deliver the data contained in the memory location
specified by the address during the clock rise of the read cycle. The direction of the pins is
controlled by OE
and the internal control logic. When OE is asserted LOW, the pins can behave
as outputs. When HIGH, DQ
s
and DQP
[A:B]
are placed in a tri-state condition. The outputs are
automatically tri-stated during the data portion of a write sequence, during the first clock when
emerging from a deselected state, and when the device is deselected, regardless of the state
of OE
.
DQP
[A:B]
I/O-
Synchronous
Bidirectional Data Parity I/O Lines. Functionally, these signals are identical to DQ
s
. During
write sequences, DQP
[A:B]
is controlled by BW
[A:B]
correspondingly.
MODE Input Strap Pin Mode Input. Selects the burst order of the device.
When tied to Gnd selects linear burst sequence. When tied to V
DD
or left floating selects
interleaved burst sequence.
V
DD
Power Supply Power supply inputs to the core of the device.
V
DDQ
I/O Power Supply Power supply for the I/O circuitry.
V
SS
Ground Ground for the device.
NC – No Connects. Not internally connected to the die.
NC/36M,
NC/72M,
NC/144M,
NC/288M
– No Connects. Not internally connected to the die. NC/36M,NC/72M, NC/144M, NC/288M are
address expansion pins are not internally connected to the die.
