OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

AD8051ARTZ-REEL7

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24
AD8051/AD8052/AD8054
Rev. J | Page 7 of 24
@ T
A
= 25°C, V
S
= ±5 V, R
L
= 2 k to ground, unless otherwise noted.
Table 3.
AD8051A/AD8052A AD8054A
Parameter Conditions Min Typ Max Min Typ Max Unit
DYNAMIC PERFORMANCE
−3 dB Small Signal Bandwidth G = +1, V
OUT
= 0.2 V p-p 70 110 85 160 MHz
G = −1, +2, V
OUT
= 0.2 V p-p 50 65 MHz
Bandwidth for 0.1 dB Flatness
G = +2, V
OUT
= 0.2 V p-p,
R
L
= 150 Ω,
R
F
= 1.1 kΩ (AD8051A/
AD8052A)
20 MHz
R
F
= 200 Ω (AD8054A) 15 MHz
Slew Rate G = −1, V
OUT
= 2 V step 105 170 150 190 V/μs
Full Power Response G = +1, V
OUT
= 2 V p-p 40 50 MHz
Settling Time to 0.1% G = −1, V
OUT
= 2 V step 50 40 MHz
NOISE/DISTORTION PERFORMANCE
Total Harmonic Distortion
f
C
= 5 MHz, V
OUT
= 2 V p-p,
G = +2
−71 −72 dB
Input Voltage Noise f = 10 kHz 16 16 nV/√Hz
Input Current Noise f = 10 kHz 900 900 fA/√Hz
Differential Gain Error (NTSC) G = +2, R
L
= 150 Ω 0.02 0.06 %
R
L
= 1 kΩ 0.02 0.02 %
Differential Phase Error (NTSC) G = +2, R
L
= 150 Ω 0.11 0.15 Degrees
R
L
= 1 kΩ 0.02 0.03 Degrees
Crosstalk f = 5 MHz, G = +2 −60 −60 dB
DC PERFORMANCE
Input Offset Voltage 1.8 11 1.8 13 mV
T
MIN
− T
MAX
27 32 mV
Offset Drift 10 15 μV/°C
Input Bias Current 1.4 2.6 2 4.5 μA
T
MIN
− T
MAX
3.5 4.5 μA
Input Offset Current 0.1 0.75 0.2 1.2 μA
Open-Loop Gain R
L
= 2 kΩ 88 96 84 96 dB
T
MIN
− T
MAX
96 96 dB
R
L
= 150 Ω 78 82 76 82 dB
T
MIN
− T
MAX
80 80 dB
INPUT CHARACTERISTICS
Input Resistance 290 300 kΩ
Input Capacitance 1.4 1.5 pF
Input Common-Mode Voltage Range
−5.2 to
+4
−5.2 to
+4
V
Common-Mode Rejection Ratio V
CM
= −5 V to +3.5 V 72 88 70 86 dB
OUTPUT CHARACTERISTICS
Output Voltage Swing R
L
= 10 kΩ
−4.98 to
+4.98
−4.97 to
+4.97
V
R
L
= 2 kΩ
−4.85 to
+4.85
−4.97 to
+4.97
−4.8 to
+4.8
−4.9 to
+4.9
V
R
L
= 150 Ω
−4.45 to
+4.3
−4.6 to
+4.6
−4.0 to
+3.8
−4.5 to
+4.5
V
Output Current V
OUT
= −4.5 V to +4.5 V 45 30 mA
T
MIN
− T
MAX
45 30 mA
Short-Circuit Current Sourcing 100 60 mA
Sinking 160 100 mA
Capacitive Load Drive G = +1 (AD8051/AD8052) 50 pF
G = +2 (AD8054) 40 pF
AD8051/AD8052/AD8054
Rev. J | Page 8 of 24
AD8051A/AD8052A AD8054A
Parameter Conditions Min Typ Max Min Typ Max Unit
POWER SUPPLY
Operating Range 3 12 3 12 V
Quiescent Current/Amplifier 4.8 5.5 2.875 3.4 mA
Power Supply Rejection Ratio ΔV
S
= ±1 68 80 68 80 dB
OPERATING TEMPERATURE RANGE RJ-5 −40 +85 °C
RM-8, R-8, RU-14, R-14 −40 +125 −40 +125 °C
AD8051/AD8052/AD8054
Rev. J | Page 9 of 24
ABSOLUTE MAXIMUM RATINGS
Table 4.
Parameter Ratings
Supply Voltage 12.6 V
Internal Power Dissipation
1
SOIC Packages
Observe power
derating curves
SOT-23 Package
Observe power
derating curves
MSOP Package
Observe power
derating curves
TSSOP Package
Observe power
derating curves
Input Voltage (Common Mode) ±V
S
Differential Input Voltage ±2.5 V
Output Short-Circuit Duration
Observe power
derating curves
Storage Temperature Range (R) −65°C to +150°C
Operating Temperature Range (A Grade) −40°C to +125°C
Lead Temperature (Soldering 10 sec) 300°C
1
See Table 5.
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
Specification is for device in free air.
Table 5. Thermal Resistance
Package Type θ
JA
Unit
8-Lead SOIC 125 °C/W
5-Lead SOT-23 180 °C/W
8-Lead MSOP 150 °C/W
14-Lead SOIC 90 °C/W
14-Lead TSSOP 120 °C/W
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the
AD8051/AD8052/AD8054 is limited by the associated rise in
junction temperature. The maximum safe junction temperature
for plastic encapsulated devices is determined by the glass
transition temperature of the plastic, approximately 150°C.
Temporarily exceeding this limit can cause a shift in parametric
performance due to a change in the stresses exerted on the die
by the package. Exceeding a junction temperature of 175°C for
an extended period can result in device failure.
While the AD8051/AD8052/AD8054 are internally short-
circuit protected, this cannot be sufficient to guarantee that the
maximum junction temperature (150°C) is not exceeded under
all conditions. To ensure proper operation, it is necessary to
observe the maximum power derating curves.
AMBIENT TEMPERATURE (°C)
–55
0
2.0
1.5
1.0
0.5
5
MAXIMUM POWER DISSIPATION (W)
2.5
MSOP-8
SOIC-8
SOT-23-5
SOIC-14
TSSOP-14
–35 –15 15 35 55 75 95 115
01062-006
Figure 6. Maximum Power Dissipation vs.
Temperature for AD8051/AD8052/AD8054
ESD CAUTION
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24

AD8051ARTZ-REEL7

Mfr. #:
Buy AD8051ARTZ-REEL7
Manufacturer:
Analog Devices Inc.
Description:
High Speed Operational Amplifiers SGL RR
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet