2
FN7489.6
May 4, 2006
Absolute Maximum Ratings (T
A
= 25°C)
V
CC
, Supply Voltage between V
S
and GND . . . . . . . . . . . . . . . . .5V
V
IN
, V
REF
. . . . . . . . . . . . . . . . . . . . . . . . . . . .VCC+0.3V, VEE-0.3V
Voltage between V
IN
and V
REF
. . . . . . . . . . . . . . . . . . . . . . . . . .±2V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 30mA
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +150°C
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C
Lead Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
AC Electrical Specifications V
CC
= DV
CC
= +3.3V, REF = GND, T
A
= 25°C, R
L
= 150Ω, unless otherwise specified.
PARAMETER DESCRIPTION CONDITIONS MIN TYP MAX UNIT
BW -3dB 3dB Bandwidth V
OUT
= 200mV
PP
200 MHz
V
OUT
= 2V
PP
100 MHz
BW 0.1dB 0.1dB Bandwidth V
OUT
= 2V
PP
50 MHz
S
R
Slew Rate V
OUT
= 2V
PP
500 V/µs
d
G
Differential Gain 0.07 %
d
P
Differential Phase 0.06 °
X
T
Hostile Crosstalk 6MHz -90 dB
I Input to Output Isolation 6MHz -70 dB
V
N
Input Noise Voltage 20 nV/√Hz
Fcp Charge Pump Switch Frequency 168 MHz
Load Reg I
EE
= 0mA to 10mA 12 60 mV
V
RIPPLE
Output Amp Ripple Voltage 30 mV
With Bead Core to DV
CC
10 mV
DC Electrical Specifications V
CC
= D
VCC
= +3.3V, REF = GND, T
A
= 25°C, R
L
= 150Ω, unless otherwise specified.
PARAMETER DESCRIPTION CONDITIONS MIN TYP MAX UNIT
V+ Supply Range 3.0 3.6 V
V
G
% Gain Error R
L
= 150Ω, V
IN
= +2.5V to -1V 1.5 %
ΔG Gain Matching R
L
= 150Ω 0.5 %
R
IN
Input Resistance V
IN
= 0V to 1.5V 1.0 1.7 15 MΩ
V
OS
Output Offset Voltage V
REF
= 0 -25 7 +25 mV
I
OUT +
Output Current R
L
= 10Ω, V
IN
= 1.2V 50 mA
I
OUT -
Output Current R
L
= 10Ω, V
IN
= -0.3V -18 mA
Z
OUT
Output Impedance Enabled 1 Ω
Three-stated 10 MΩ
PSRR Power Supply Rejection Ratio 60 90 dB
I
S
Supply Current Amp Enabled 120 150 mA
Amp Disabled 80 mA
R
REF
Input Reference Resistor 4 5 6 kΩ
ISL59830
