D1U4-W-1600-12-HA2C

D1U4-W-1600-12-Hx Series
AC/DC Front End Power Supply
CPS_D1U4-W-1600-12-Hx.B02 Page 4 of 6
www.murata-ps.com/support
OUTPUT CONNECTOR AND SIGNAL SPECIFICATION
DC and Signal Connector: Tyco Part # 1-6450132-2, or FCI PowerBlade # 51732-021
Pin Assignment Signal Name Description
High Level
Low Level
I Max
P1, P2, P7, P8 VOUT Main output voltage
P3, P4, P5, P6 VRTN Main output voltage, return
A1 Sense +
VOUT remote sense, positive node input, connected to the
+ve load point
A2 Sense -
VOUT remote sense, negative node input, connected to the
-ve load point
C5, C6, D5, D6 V_SB Standby voltage output
C3, C4, D3, D4 V_SB Return Standby voltage, return, tied internally to Output Return
B1 I_Share Active load sharing bus 0 – 8V -4 mA / +5 mA
D1 AC_OK
Input AC Voltage “OK” signal output (Internal pull up is
10kΩ to Vsb)
>2.4V (active, OK)
<0.4V
+4 mA
-2 mA
D2 P_Good Power good signal output (Internal pull up is 10kΩ to Vsb)
>2.4V (active, Good)
<0.4V
+4 mA
-2 mA
B5 PS_Kill
Floating pin will turn off P/S (shorter pin, last-make and
first-break contact for hot plugging). This signal overrides
PS-On in disabling the Main Output
>2.1V (open, or Vsb)
<0.7V (active, PS:On)
N/A
B6 PS_Present Internally tied to Vsb return 0 V
A6 PS_On
Internal 1K ohm pull-up to Vsb, (accepts open collector/
drain drive), This signal to be pulled low to turn-on power
supply
>2.1V (open, or Vsb)
<0.7V (active, PS:On)
-4 mA
-1 mA
A3 I
2
C Data I
2
C serial data bus Vsb
A4 I
2
C Clock I
2
C serial clock bus Vsb
B2 I
2
C Adr0 Address input 0, internal pull-up to Vsb
>2.1V, < Vsb
<0.8V
±1 mA
B3 I
2
C Adr1 Address input 1, internal pull-up to Vsb
>2.1V, <Vsb
<0.8V
±1 mA
B4 I
2
C Adr2 Address input 2, internal pull-up to Vsb
>2.1V, <Vsb
<0.8V
±1 mA
D1U4 MATING CONNECTORS
12V D1U4 mating connector
Press Fit Solder
1
Straight Right Angle Straight Right Angle
Murata-PS N/A N/A N/A 36-0430032-0
FCI 51742-10802400CALF 51762-10802400CBLF 51742-10802400AALF 51762-10802400ABLF
Tyco TBD TBD TBD TBD
1 Solder connector recommended for board thickness of <0.090
P1 P2 P3 P4 P5 P6 P7 P8 x1 x2 x3 x4 x5 x6
VOUT VOUT VRTN VRTN VRTN VRTN VOUT VOUT
AC_OK P_GOOD
V_SB
RETURN
V_SB
RETURN
V_SB
+OUT
V_SB
+OUT
D
SPARE SPARE
V_SB
RETURN
V_SB
RETURN
V_SB
+OUT
V_SB
+OUT
C
I_SHARE I
2
C ADR0 I
2
C ADR1 I
2
C ADR2 PS_KILL
PS_
PRESENT
B
SENSE + SENSE - I
2
C DATA
I
2
C
CLOCK
SPARE PS_ON A
mate-last pins
D1U4-W-1600-12-Hx Series
AC/DC Front End Power Supply
CPS_D1U4-W-1600-12-Hx.B02 Page 5 of 6
www.murata-ps.com/support
WIRING DIAGRAM FOR OUTPUT
CURRENT SHARING NOTES
12V Output: Current sharing is achieved using the active current share method. (See wiring diagram for connection details.)
The total combined load must be below 1600W at startup. Current sharing can be achieved with or without remote sense connected to the common load.
V_SB outputs can be tied together for redundancy but total combined output power must not exceed 20W. The V_SB output has internal ORing MOSFET for
additional redundancy / internal short protection.
The current share pin B1 is a connection between the two units. It is input and/or output as the voltage on the line controls the current share. A power
supply will respond to a change in this voltage but a power supply can also change the voltage depending on the load drawn from it. On a single unit this
would read 8V at 100% load. For two units sharing load then this should read 4V for perfect current sharing.
Up to 6 units can be paralleled together. Please consult your Murata sales representative if operation with more than six units in parallel is needed.
VRTN
Sense + (Main Output Remote Sense)
Sense -
VOUT
A1
P1, P2, P7, P8
P3, P4, P5, P6
A2
Dotted lines show optional remote sense connections.
Optional remote sense lines can be attached to a load that is a distance
away from the power supply to improve regulation at the load.
D1U4
12V load
A6
C3, C4, D3, D4
C5, C6, D5, D6
Close switch (or FET, BJT, or wire)
to turn on +12V OUT
+5V logic circuitry
V_SB
PS_On
V_SB Return
B5 PS_Kill
D1U4
B1 I_Share
PS_Kill
B5
C3, C4, D3, D4V_SB Return
PS_On
C5, C6, D5, D6V_SB
B1
A2
Sense -
I_Share
VRTN
VOUT
Sense + (Main Output Remote Sense)
A1
P1, P2, P7, P8
P3, P4, P5, P6
A6
D1U4-W-1600-12-Hx Series
AC/DC Front End Power Supply
CPS_D1U4-W-1600-12-Hx.B02 Page 6 of 6
www.murata-ps.com/support
Murata Power Solutions, Inc. makes no representation that the use of its products in the circuits described herein, or the use of other
technical information contained herein, will not infringe upon existing or future patent rights. The descriptions contained herein do not imply
the granting of licenses to make, use, or sell equipment constructed in accordance therewith. Specifications are subject to change without
notice. © 2016 Murata Power Solutions, Inc.
Murata Power Solutions, Inc.
11 Cabot Boulevard, Mansfield, MA 02048-1151 U.S.A.
ISO 9001 and 14001 REGISTERED
This product is subject to the following operating requirements
and the Life and Safety Critical Application Sales Policy:
Refer to: http://www.murata-ps.com/requirements/
MECHANICAL DIMENSIONS - D1U-W-1200-12-Hx
OPTIONAL ACCESSORIES
Description Part Number
12V D1U-12 output connector card D1U-12-CONC
APPLICATION NOTES
Document Number Description Link
ACAN-27 D1U-12-CONC Output Connector Card www.murata-ps.com/data/apnotes/acan-27.pdf
ACAN-31 D1U4 Communications Protocol www.murata-ps.com/data/apnotes/acan-31.pdf
Dimensions: 4.00" x 14.00"x 1.61" [101.6mm x 355.6mm x 40.64mm] AC Input Connector: The AC input connector is standard IEC C20 20A.
101,60
±
0,65
4.000
±
0.025[ ]
355,60
±
0,65
14.000
±
0.025[ ]
REF
8,88
0.350[ ]
358,48
±
0,65
14.113
±
0.025[ ]
41,00
±
0,40
1.614
±
0.015[ ]
9,68
±
0,40
0.381
±
0.015[ ]
2,40
±
0,25
0.094
±
0.009[ ]
12,63
±
0,40
0.497
±
0.015[ ]
SCALE 0.700
Airflow Back to Front

D1U4-W-1600-12-HA2C

Mfr. #:
Manufacturer:
Description:
Switching Power Supplies 1600W 12Vmain 5Vsb back-front airflow
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union