NCS37005MNTWG

© Semiconductor Components Industries, LLC, 2012
April, 2012 Rev. P0
1 Publication Order Number:
NCS37005/D
NCS37005
Product Preview
Ground Fault Interrupter
(GFI)
Description
The NCS37005 is a signal processor for GFI applications. The
device integrates a flexible power supply (including both shunt and
LDO regulators), and differential fault detection circuits. The
proprietary fault processing circuitry offers high performance with
low turns ratio ferrite current transformers. The device also includes a
specialized DSP controller that offers best in class immunity to
nuisance loads without the need for external analog filters.
Features
6.0 – 18 Volt Operation (120 480 V AC Mains with the Appropriate
Series Impedance)
40 to 85°C
Very Low Power Consumption: <5 mW @ 5 V
16 Pin QFN Package
Low Cost/Turns Ratio Ferrite Current Transformer (CT) Detection of
Differential
Self Syncing Internal Oscillator Adjusts to AC Mains Frequency to
Guarantee Full Resolution on 50 and 60 Hz Distribution Systems
Optimized Solenoid Deployment (coil is not energized near the AC
mains zero crossings)
Randomized Testing Sequence to Minimize Noise and Potential
Interactions on the AC Mains
>5 mA SCR Driver for Additional Immunity to Supply
Noise/Interference
Superior Immunity to Nuisance Loads/Noise (up to 10 A) without
Loss of Detection Capability or CT Saturation
These Devices are PbFree, Halogen Free/BFR Free and are RoHS
Compliant
Typical Applications
Load Panel GFI/RCD Breakers
GFI Receptacles
Inline GFI Circuits (power cords)
This document contains information on a product under development. ON Semiconductor
reserves the right to change or discontinue this product without notice.
1
http://onsemi.com
QFN 16
MN SUFFIX
CASE 485G
MARKING DIAGRAM
PIN CONNECTIONS
XXXXX = Specific Device Code
A = Assembly Location
L = Wafer Lot
Y = Year
W = Work Week
G or G = PbFree Package
CCCCC = Country of Origin
XXXXX
ALYWG
CCCCC
MLD
CTresGN
CTbias
CTstim
CTresD
IDF
Supply
SCRdrv
GND
(Top View)
Device Package Shipping
NCS37005MNTWG QFN16 Tape & Reel
NCS37005MNG QFN16 Tube
ORDERING INFORMATION
NCS37005DARG TSSOP20 Tape & Reel
NCS37005DAG TSSOP20 Tube
1
For information on tape and reel specifications,
including part orientation and tape sizes, please
refer to our Tape and Reel Packaging Specification
Brochure, BRD8011/D.
1
16
TSSOP 16
DA SUFFIX
CASE 948F
NCS37005
http://onsemi.com
2
Control Logic and
Digital Filter
IDF
Supply
TE
Self
Trimmed
RC Osc
Waveform
Generator
HV
Bandgap
POR
Brown
Out
SCRdrv
Driver
Vbias
Low
Pass
Filter
CTbias
CTstim
CTresGN
VSS
+
+
AVDD/
DVDD
Mixer
Differential Current
Detection
Grounded Neutral
Detection
Offset
Correction
G2N
Randomizer
Mains Level
Detect (Zero
Cross)
MLD
CTresD
TestDin15
TestDout12
Figure 1. Simplified Block Diagram
NCS37005
http://onsemi.com
3
Table 1. PIN FUNCTION DESCRIPTION QFN
Pin # Name Pad Description
0 Ground QFN center slug
1 MLD Mains Level Detect (Zero Cross)
2 CTtest Test port (Must be tied to CTbias in functional mode).
3 CTbias 2 V reference that is connected to the external CT sensor
4 CTstim Differential current measurement port for external CT
5 CTresD Determines IV converter gain for detection threshold / matched to CT turns ratio (Differential Current)
6 IDF Front end noise filter capacitor
7 NC Tie to Ground or leave floating
8 NC Tie to Ground or leave floating
9 NC Tie to Ground or leave floating
10 NC Tie to Ground or leave floating
11 NC Tie to Ground or leave floating
12 NC Tie to Ground or leave floating
13 NC Float
14 NC Float
15 SCRdrv Used to trigger the solenoid at a fault detection
16 Supply Power supply
Table 2. PIN FUNCTION DESCRIPTION TSSOP
Pin # Name Pad Description
1 CTstim Differential current measurement port for external CT
2 Ground Main ground connection for IC.
3 CTresD Determines IV converter gain for detection threshold / matched to CT turns ratio (Differential Current)
4 IDF Front end noise filter capacitor
5 TE Test enable
6 NC Tie to Ground or leave floating
7 NC Tie to Ground or leave floating
8 NC Tie to Ground or leave floating
9 NC Tie to Ground or leave floating
10 NC Tie to Ground or leave floating
11 NC Float
12 NC Float
13 SCRdrv Used to trigger the solenoid at a fault detection
14 Supply Power supply
15 MLD Mains Level Detect (Zero Cross)
16 CTbias 2 V reference that is connected to the external CT sensor

NCS37005MNTWG

Mfr. #:
Manufacturer:
ON Semiconductor
Description:
IC GFCI CTLR CDM 16QFN
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet