OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

PLT09HN2003R0P1B

P1-P3P4-P6
Spec. No. JEFL243B – 0003F-01 P 1/ 6
MURATA MFG CO.,LTD.
Reference
Only
DC Common Mode Choke Coil
PLT09HN2003R0P1B Reference
Specification
1. Scope
This reference specification applies to DC Common Mode Choke Coil (PLT09H Series).
2. Part Numbering
(Ex.)
PL T 09 H N 200 3R0 P 1 B
Product ID Type Applications Structure Safety Inductance
Rated Winding Mode Lead Packaging
Standard Current Dimensions (B:Bulk)
(N:Not certified) (P:Aligned Winding)
3. Rating
Item Specification
Customer Part Number
Murata Part Number PLT09HN2003R0P1B
Rated Voltage 50 V(DC)
Rated Current 3 A
Withstand Voltage 125 V(DC) (1 minute)
Insulation Resistance 10 M min.
Direct Current Resistance 0.03 max.
Inductance L1,L2 20 H min.
Inductance Difference | L1-L2 | 2 H max.
Temperature Characteristic
(Inductance change)
within ±
８０
５０
%
Temperature Rise 30 °C max.
Operating Temperature Range
(Ambient Temperature)
- 40 °C to + 85 °C
Storage Temperature Range - 40 °C to + 85 °C
4. Standard Testing Conditions
< Unless otherwise specified > < In case of doubt >
Temperature : Ordinary Temp. 15 ºC to 35 °C Temperature : 20 °C ± 2 °C
Humidity : Ordinary Humidity 25 %(RH) to 85 %(RH) Humidity : 60 %(RH) to 70 %(RH)
Atmospheric pressure : 86 kPa to 106 kPa
5. Appearance,Dimensions and Equivalent Circuit Diagram
See Fig.1.
6. Marking
(1) Inductance :
200
(2) Manufacturer Identification :
7. Electrical Performance
No. Item Specification Test Method
7.1 Inductance
L1,L2 |L1 - L2|
Meet item 3. Measuring terminal : T1-T2(L1) , T3-T4(L2)
Frequency : 1 kHz
7.2 Insulation
Resistance
Measuring terminal : (T1,T2) – (T3,T4)
Test Voltage : 100 V(DC)
Time : 1 minute
7.3 Direct Current
Resistance
Measuring terminal : T1-T2 , T3-T4
Spec. No. JEFL243B – 0003F-01 P 2/ 6
MURATA MFG CO.,LTD.
Reference
Only
No. Item Specification Test Method
7.4 Temperature
Characteristics
Meet item 3. Inductance shall be measured at each step
specified in Table 1 after reaching the thermal
epuilibrium.
The inductance change against the inductance at
step 3 shall be calculated.
Table 1
7.5 Temperature rise The surface of coil : 30 °C max. Applying Current : Rated Current
7.6 Withstand
Voltage
Products shall be no failure. Measuring terminal : (T1,T2) - (T3,T4)
(between terminals)
Test Voltage : 125 V(DC) (1 minute)
8. Mechanical Performance
No. Item Specification Test Method
8.1 Appearance and
Dimensions
There shall not be a conspicuous
dirt, crack,and so on.
Dimensions shall be as shown in Fig.1.
Visual Inspection
Measured with slide calipers
8.2 Lead wire
Strength
Products shall not be damaged.
(cutting of lead wire, missing of pin,
etc.)
The body of products shall be fixed, and the force
of 5N shall be applied gradually and sustained for
30s to each lead wires in the axial direction of
the lead wires.
8.3 Solderability The lead wires shall be covered
with new solder at least 75% along
the circumference of the immersed
part.
Flux : Ethanol solution of rosin, 25(wt)%
Pre-heat : 150 ± 10 °C, 60 ~ 90 s
Solder : Sn-3Ag-0.5Cu
Solder Temperature : 245 ± 5 °C
Immersion Time : 2 ± 0.5 s
Immersion Depth : 2.6 ± 0.8 mm from the root of
lead wire
8.4 Resistance to
soldering heat
Meet Table 2.
Table 2
Flux : Ethanol solution of rosin, 25(wt)%
Pre-heat : 150 ± 10 °C, 60 ~ 90 s
Solder : Sn-3Ag-0.5Cu
Solder Temperature : 260 ± 5 °C
Immersion Time : 10 ± 1 s
Immersion Depth : 2.6 ± 0.8 mm from the root of
lead wire
Then measured after exposure in the room
condition for 4 to 24 hours.
8.5 Vibration Vibration Frequency : 10Hz to 55Hz to 10Hz
for 1 minute
Amplitude : 1.5 mm
Time : A period of 2 hours in each of 3 mutually
perpendicular directions. (Total 6 hours)
8.6 Shock Maximum Acceleration : 981 m / s
2
Normal Duration : 6 ms
Wave form : Half-sine wave
Velocity Change : 3.75 m / s
Direction : along the three mutually perpendicular
axes of the product
Times : Three shocks in each directions
(total 18 times)
Appearance No damage
Inductance
Change
within ± 10 %
Withstand
Voltage
Meet item 7.6
Step Temperature Step Temperature
1 +20 ± 2 °C 4 +85 ± 2 °C
2 -25 ± 2 °C 5 +20 ± 2 °C
3 +20 ± 2 °C
Spec. No. JEFL243B – 0003F-01 P 3/ 6
MURATA MFG CO.,LTD.
Reference
Only
9. Enviromental Performance
No. Item Specification Test Method
9.1 Temperature
Cycle
Meet Table 2. 1 cycle :
1 step : - 40 °C (+ 0 °C, - 3 °C) / 30 min.
2 step : Ordinary Temp. / 3 min. max.
3 step : + 85 °C (+ 3 °C, - 0 °C) / 30 min.
4 step : Ordinary Temp. / 3 min. max.
Total of 10 cycles
Then measured after exposure in the room
condition for 4 to 24 hours.
9.2 Humidity Temperature : 40 °C ± 2 °C
Humidity : 90 %(RH) to 95 %(RH)
Time : 1000 h (+24h , -0h)
Then measured after exposure in the room
condition for 4 to 24 hours.
9.3 Cold Resistance Temperature : - 40 °C ± 2 °C
Time : 1000 h (+24h , -0h)
Then measured after exposure in the room
condition for 4 to 24 hours.
9.4 Heat Resistance Temperature : 85 °C ± 2 °C
Time : 1000 h (+24h , -0h)
Then measured after exposure in the room
condition for 4 to 24 hours.
9.5 Heat Life Temperature : 85 °C ± 2 °C
Test Voltage : 50 V(DC)
Time : 1000 h (+24h , -0h)
Then measured after exposure in the room
condition for 4 to 24 hours.
10. Insertion Loss (Typical)
Insertion Loss measuring circuit
Measuring circuit (based on MIL-STD-220)
A = 20 log(E1/E2)
A : Insertion Loss (dB)
E1 : Level with Common mode choke coil
E2 : Level without Common mode choke coil
11. Specification of Packaging
11.1.Packing Quantity
Individual packaging
100pcs
11.2.
Packing Method
Styrene foam of the stuck products on are placed in an Individual packaging .
A quantity in an Outer packaging is depending on a quantity of an order.
50
10dB
SG
LM
50
50
10dB
50
Attenuator
Attenuator
Sample
T1
T2
T4
T3
P1-P3P4-P6

PLT09HN2003R0P1B

Mfr. #:
Buy PLT09HN2003R0P1B
Manufacturer:
Description:
Common Mode Filters / Chokes 3.0 AMP AC COMMON CH
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet