OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

5962-8851301PA

P1-P3P4-P6P7-P9P10-P12
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88513
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
4
DSCC FORM 2234
APR 97
2. APPLICABLE DOCUMENTS
2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part
of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the
solicitation or contract.
DEPARTMENT OF DEFENSE SPECIFICATION
MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for.
DEPARTMENT OF DEFENSE STANDARDS
MIL-STD-883 - Test Method Standard Microcircuits.
MIL-STD-1835 - Interface Standard Electronic Component Case Outlines.
DEPARTMENT OF DEFENSE HANDBOOKS
MIL-HDBK-103 - List of Standard Microcircuit Drawings.
MIL-HDBK-780 - Standard Microcircuit Drawings.
(Copies of these documents are available online at http://quicksearch.dla.mil
or from the Standardization Document Order
Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)
2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text
of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a
specific exemption has been obtained.
3. REQUIREMENTS
3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with
MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The
modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for
device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified
herein.
3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified
in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.
3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein .
3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the
electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full
ambient operating temperature range.
3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical
tests for each subgroup are defined in table I.
3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be
marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer
has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be
marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be
in accordance with MIL-PRF-38535, appendix A.
3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in
MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.
TABLE I. Electrical performance characteristics.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88513
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
5
DSCC FORM 2234
APR 97
Test
Symbol
Conditions 1/
-55°C ≤ T
A
≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits
Unit
Min
Max
Input offset voltage
V
OS
1
01
±1.0
mV
02
±1.5
2,3
All
±2.0
Input bias current
I
IB
1
All
±200
pA
2,3 2/
±20
nA
Input offset current
I
OS
1
All
±40
pA
2,3 2/
±1
nA
Common mode 3/
rejection
CMR
V
CM
= IVR = ±11 V
1
All
86
dB
2,3
80
Power supply rejection
ratio
PSRR
V
S
= ±10 V to ±20 V
1
All
40
µV/V
2,3
50
Short circuit output
current
I
SC
Output shorted to ground
1
All
20
60
mA
2,3
8
60
Supply current
I
SY
V
O
= 0 V, no load
1,2,3
All
6.0
mA
External V
OS
trim range
V
OS
R
POT
= 10 kΩ,
T
A
= +25°C
1
All
±2.5
±10
mV
Output voltage swing
V
O
R
L
= 1 kΩ
4
All
±11.5
V
R
L
= 2 kΩ
5,6
±11.0
Large signal voltage gain
A
VO
R
L
= 10 kΩ, V
O
= ±10 V
4
All
500
V/mV
5,6
160
R
L
= 2 kΩ, V
O
= ±10 V
4
200
5,6
80
R
L
= 1 kΩ, V
O
= ±10 V,
T
A
= +25°C
4
100
See footnotes at end of table.
STANDARD
MICROCIRCUIT DRAWING
SIZE
A
5962-88513
DLA LAND AND MARITIME
COLUMBUS, OHIO 43218-3990
REVISION LEVEL
G
SHEET
6
DSCC FORM 2234
APR 97
TABLE I. Electrical performance characteristics – Continued.
Test
Symbol
Conditions 1/
-55°C ≤ T
A
≤ +125°C
unless otherwise specified
Group A
subgroups
Device
type
Limits
Unit
Min
Max
Slew rate 4/
SR
A
VCL
= +1, R
L
= 2 kΩ
7
All
45
V/µs
8
40
Input offset voltage
temperature coefficient
TCV
OS
T
A
= -55°C, +125°C
8
All
10
µV/°C
Settling time
t
S
See figure 2, T
A
= +25°C,
0.1 % for 10 V step
9
All
1.0
µs
1/ Unless otherwise specified, V
S
= ±15 V, V
CM
= 0 V, R
S
= 50 Ω, and T
A
= T
J
.
2/ Subgroup 3, if not tested, shall be guaranteed to the limits specified in table I herein.
3/ IVR is defined as the V
CM
range used for the CMR test.
4/ Slew rate may be specified separately for positive and negative going changes.
3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535
listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of
compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see
6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of
supply for this drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-
PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.
3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for
device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.
3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of
product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing.
3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritime 's agent,
and the acquiring activity retain the option to review the manufacturer's facility and applicable required documentation. Offshore
documentation shall be made available onshore at the option of the reviewer.
3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in
microcircuit group number 49 (see MIL-PRF-38535, appendix A).
P1-P3P4-P6P7-P9P10-P12

5962-8851301PA

Mfr. #:
Buy 5962-8851301PA
Manufacturer:
Analog Devices Inc.
Description:
Precision Amplifiers HI-SPD FAST SETTL PREC IC
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet