LQM2HPN2R2MG0L

Spec No. JELF243B-0019K-01 P.1/9
MURATA MFG.CO., LTD
Reference
Only
Operating Temperature (°C)
85 125
0
Rated Current (A)
at 85°C
Rated current
at 125°C
Rated current
CHIP COIL (CHIP INDUCTORS) LQM2HPN□□□□G0L REFERENCE SPECIFICATION
1. Scope
This reference specification applies to LQM2HPN_G0 series, Chip Coil (Chip Inductors).
2. Part Numbering
(ex) LQ M 2H P N 1R0 M G 0 L
Product ID Structure Dimension Applications Category Inductance Tolerance Dimension Other Packaging
(L×W) and (T)
L: Taping
Characteristics *B: BULK
*B: Bulk packing also available
3. Rating
Operating Temperature Range. – 55°C to +125°C
Storage Temperature Range. – 55°C to
+125°C
Customer
Part Number
MURATA
Part Number
Inductance
DC Resistance
()
Self
Resonant
Frequency
Rated Current*
1
(A)
(μH) Tolerance
Typ Max (MHz min.) 85*
2
125*
2
LQM2HPNR47MG0L 0.47
±20%
0.040 0.050 100 1.8 1.3
LQM2HPN1R0MG0L 1.0 0.055 0.069 60 1.6 1.2
LQM2HPN1R5MG0L 1.5 0.070 0.088 50 1.5 1.1
LQM2HPN2R2MG0L 2.2 0.080 0.10 40 1.3 0.97
LQM2HPN3R3MG0L 3.3 0.10 0.125 30 1.2 0.9
LQM2HPN4R7MG0L 4.7 0.11 0.138 25 1.1 0.82
*1 When applied Rated current to the Products, temperature rise caused by self-generated heat shall be limited to
40 max
*2 As for the Rated current marked with
*2
,
Rated Current is derated as right figure
depending on the operating temperature.
4. Testing Conditions
Unless otherwise specified In case of doubt
Temperature : Ordinary Temperature / 15°C to 35°C Temperature : 20°C ± 2°C
Humidity
: Ordinary Humidity / 25%(RH) to 85%(RH) Humidity : 60%(RH) to 70%(RH)
Atmospheric Pressure : 86kPa to 106kPa
Spec No. JELF243B-0019K-01 P.2/9
MURATA MFG.CO., LTD
Reference
Only
5. Appearance and Dimensions
Unit Mass (Typical value)
0.022g
(in mm)
6. Electrical Performance
No. Item Specification Test Method
6.1 Inductance
Inductance shall meet item 3. Measuring Equipment:
Agilent 4294A or equivalent (1mA)
Measuring Frequency: 1MHz
6.2 DC Resistance DC Resistance shall meet item 3. Measuring Equipment: Digital multi meter
DC resistance shall be measured after
putting chip coil between the terminal 2
under the condition of opening between
a and b.
Every measurement the terminal 1 shall
be shorted between a and b when
changing chip coil.
6.3 Self Resonant
Frequency
(S.R.F)
S.R.F shall meet item 3. Measuring Equipment:
Agilent 4294A or equivalent
6.4 Rated Current Self temperature rise shall be
limited to 40°C max.
The rated current is applied.
Digital multi meter
(TR6846 or equivalent)
terminal2terminal1
SW
a
b
0.6±0.2
2.5±0.2
2.0±0.2
0.9±0.1
Spec No. JELF243B-0019K-01 P.3/9
MURATA MFG.CO., LTD
Reference
Only
7. Mechanical Performance
No. Item Specification Test Method
7.1 Shear Test Chip coil shall not be damaged after
tested as follows.
Applied Direction
Force: 10N
Hold Duration: 5s±1s
Applied Direction: Parallel to PCB
7.2 Bending Test
Substrate: Glass-epoxy substrate
(100mm×40mm×1.0mm)
(in mm)
Speed of Applying Force: 0.5mm / s
Deflection: 3mm
Hold Duration: 30 s
7.3 Vibration Oscillation Frequency:
10Hz to 2000Hz to 10Hz for 20 min
Total amplitude 3.0 mm or Acceleration
amplitude 245m/s
2
whichever is smaller.
Testing Time:
A period of 4h in each of 3 mutually
perpendicular directions.
7.4 Drop Chip coil shall not be damaged after
tested as follows.
It shall be dropped on concrete or steel
board.
Method : free fall
Height : 1m
Total of 10 cycles
7.5 Solderability The wetting area of the electrode
shall be at least 90% covered with
new solder coating.
Flux: Ethanol solution of rosin 25(wt)%
(Immersed for 5s to 10s)
Solder: Sn-3.0Ag-0.5Cu
Pre-Heating: 150°C±10°C / 60s to 90s
Solder Temperature: 240°C±5°C
Immersion Time: 3s±1s
7.6 Resistance to
Soldering Heat
Appearance: No damage
Inductance Change: within ±30%
Flux: Ethanol solution of rosin 25(wt)%
(Immersed for 5s to 10s)
Solder: Sn-3.0Ag-0.5Cu
Pre-Heating: 150°C±10°C / 60s to 90s
Solder Temperature: 270°C±5°C
Immersion Time: 10s±1s
Then measured after exposure in the room
condition for 24h±2h.
F
Chip Coil
Substrate
F
Pressure jig
R230
Deflection
Product
45
45

LQM2HPN2R2MG0L

Mfr. #:
Manufacturer:
Description:
Fixed Inductors 1008 2.2uH 20%
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union