DLP31DN441ML4L Datasheet DLP31DN201ML4L, DLP31DN131ML4L, DLP31DN900ML4L | P1-P3

Spec No. JEFL243E-0003L-01 P1/10

MURATA MFG.CO., LTD

Reference

Only

0.3±0.2

1.6±0.15

1.15±0.15

□：

Electrode

：

3.2±0.15

(5)

(6)

(7)

(8)

(1)

(2)

(3)

(4)

0.4±0.2

0.8±0.1

Chip Common Mode Choke Coil

DLP31DN□□□ML4□ Reference Specification

1.Scope

This reference specification applies to Chip Common Mode Choke Coil DLP31DN_ML Series

2.Part Numbering

(ex.) DL P 31 D N 441 M L 4 L

(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)

(1) Chip Common Mode Choke Coil

(2) Structure (P : Film Type)

(3) Dimension (LW)

(4) Type

(5) Category

3.Rating

Customer

Part Number

Murata

Part Number

Common Mode Impedance

(at 100MHz, Under

Standard Testing Condition)

Rated

Voltage

Withstanding

Voltage

Rated

Current

Resistance

Insulation

Resistance

DLP31DN900ML4L

90Ω ±20%

10V(DC) 25V(DC)

160mA

1.1Ωmax.

100MΩ

min.

DLP31DN900ML4B

DLP31DN131ML4L

130Ω ±20%

120mA

1.6Ωmax.

DLP31DN131ML4B

DLP31DN201ML4L

200Ω ±20%

100mA

2.2Ωmax.

DLP31DN201ML4B

DLP31DN321ML4L

320Ω ±20%

80mA

3.5Ωmax.

DLP31DN321ML4B

DLP31DN441ML4L

440Ω ±20%

70mA

4.3Ωmax.

DLP31DN441ML4B

Operating Temperature : -40 to +85°C Storage Temperature : -40 to +85°C

4. Standard Testing Conditions

Unless otherwise specified> <In case of doubt>

Temperature : Ordinary Temperature 15 to 35°C Temperature : 20 ± 2°C

Humidity : Ordinary Humidity 25 to 85%(RH) Humidity : 60 to 70%(RH)

Atmospheric Pressure : 86 to106kPa

5.Style and Dimensions

■ Equivalent Circuits

■ Unit Mass(Typical value)

0.030g

6.Marking

No Marking.

(4)

(3)

(2)

(1)

(5)

(6)

(7)

(8)

(6) Impedance (Typ. at 100MHz)

(7) Circuit

(8) Features

(9) Number of Line

(10) Packaging Code L : Taping / B : Bulk

Spec No. JEFL243E-0003L-01 P2/10

MURATA MFG.CO., LTD

Reference

Only

7. Electrical Performance

No. Item Specification Test Method

7.1 Common Mode

Impedance

Meet item 3. Measuring Frequency : 100±1MHz (ref.item 10.)

Measuring Equipment : Agilent 4291A or the

equivalents

(In case of doubt in standard condition, the heat

treatment (200°C,about 10 minutes)shall be applied.

7.2 Withstanding

Voltage

Products shall not be damaged. Test Voltage : 2.5 times for Rated Voltage

Time : 1 to 5 seconds

Charge Current : 1 mA max.(ref.item 10.)

7.3 DC Resistance

(Rdc)

Meet item 3. Measuring current : 10mA max.(ref.item 10.)

7.4 Insulation

Resistance (I.R.)

Measuring voltage : Rated Voltage

Measuring time : 1 minute max. (ref.item 10.)

8.Mechanical Performance

No. Item Specification Test Method

8.1 Appearance and

Dimensions

Meet item 5.

Visual Inspection and measured with Slide Calipers.

8.2 Solderability The electrodes shall be at least

95% covered with new solder

coating.

Flux : Ethanol solution of rosin,25(wt)%

Pre-Heating : 150°C, 1minute

Solder : Sn-3.0Ag-0.5Cu

Solder Temperature : 245±5°C

Immersion Time : 3±1 seconds

Immersion and emersion rates : 25 mm / s

8.3 Resistance to

Soldering Heat

Meet Table 1.

Table 1

Flux : Ethanol solution of rosin,25(wt)%

Pre-Heating : 150°C, 1minute

Solder : Sn-3.0Ag-0.5Cu

Solder Temperature : 270±5°C

Immersion Time : 10±0.5 seconds

Immersion and emersion rates : 25 mm / s

Then measured arter exposure in the room condition

for 4 to 48 hours.

8.4 Bending

Strength

Substrate : (t =1.6 mm).

Deflection : 2 mm

Speed of Applying Force : 0.5 mm / s

Keeping time : 30 seconds

8.5 Drop Products shall be no failure. It shall be dropped on concrete or steel board.

Method : free fall

Height : 1m

The Number of Times

: 3 times for each direction (Total 9 times)

8.6 Vibration Meet Table 1. It shall be soldered on the substrate.

Oscillation Frequency : 10 to 55 to 10Hz for 1 minute

Total Amplitude : 1.5mm

Testing Time : A period of 2 hours in each of 3

mutually perpendicular directions.

Appearance No damaged

Common Mode

Impedance

Change

within ± 20%

I.R.

100MΩ min.

DC Resistance

Change

within ± 30%

Rdc

R230

Deflection

Product

Pressure jig

(in mm)

Spec No. JEFL243E-0003L-01 P3/10

MURATA MFG.CO., LTD

Reference

Only

9.Environmental Performance (Products shall be solderd on the glass-epoxy substrate)

No. Item Specification Test Method

9.1 Temperature

Cycle

Meet Table 1. 1 Cycle

Step 1 -40°C(+0°C,-3°C) / 30±3 min

Step 2 Ordinary Temp. / 10 to 15 min

Step 3 +85(+3°C,-0°C) / 30±3 min

Step 4 Ordinary Temp. / 10 to 15 min

Total of 100 cycles.

Then measured after exposure in the room condition

for 4 to 48 hours.

9.2 Humidity Temperature : 40±2°C

Humidity : 90 to 95 % (RH)

Time : 1000 hours(+48 hours,-0 hours)

Then measured after exposure in the room condition

for 4 to 48 hours.

9.3 Heat life Temperature : 85±2°C

Test Voltage : 2 times for Rated Voltage

Time : 1000 hours(+48 hours,-0 hours)

Then measured after exposure in the room condition

for 4 to 48 hours. (ref. Item

10.)

9.4 Cold Resistance Temperature : -40± 2°C

Time : 1000 hours(+48 hours,-0 hours)

Then measured after exposure in the room condition

for 4 to 48 hours.

10. Terminal to be Tested.

When measuring and suppling the voltage,the following terminal is applied.

No. Item Terminal to be Tested

10.1 Common Mode

Impedance

(Measurement Terminal)

10.2 Withstanding Voltage

(Measurement Terminal)

Insulation Resistance

(Measurement Terminal)

Heat Life

(Supply Terminal)

10.3 DC Resistance

(Measurement Terminal)

11. Measuring method for common mode impedance.

Measured common mode impedance may be included measurement error due to stray capacitance,

residual inductance of test fixture.

To correct this error, the common mode impedance should be calculate as follows;

(1) Measure admittance of the fixture(opened), Go Bo.

(2) Measure impedance of the fixture(shorted), Rs Xs.

(3) Measure admittance of the specimen, Gm Bm.

(4) Calculate corrected impedance Z using the formula below.

Z = (Rx

+Xx

)

1/2

Where

Rx =

Gm-Go

(Gm-Go)

２

+ (Bm-Bo)

２

- Rs

Xx =

-(Bm- Bo)

(Gm-Go)

２

+ (Bm-Bo)

２

- Xs

Terminmal

Terminal

Terminal Terminal

Terminal

Terminmal

P1-P3 P4-P6 P7-P9

DLP31DN441ML4L

Mfr. #:

Buy DLP31DN441ML4L

Manufacturer:

Description:

Common Mode Filters / Chokes 440ohms

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

DLP31DN441ML4L

DLP31DN441ML4L

Products related to this Datasheet