OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

LQW32FT100M0HL

P1-P3P4-P6P7-P8
SpecNo.JELF243A-9147A-01 P.1/8
MURATA MFG.CO.,LTD
Reference Only
CHIP COIL (CHIP INDUCTORS) LQW32FT□□□□0HL
Murata Standard Reference Specification 【AEC-Q200】
1. Scope
This reference specification applies to Chip coil (Chip Inductors) LQW32FT_0H series for Automotive Electronics based
on AEC-Q200.
2. Part Numbering
(ex) LQ W 32 F T 470 M 0 H L
Product ID
Structure
Dimension
Applications Category Inductance Tolerance Features
Category
Packaging
(L×W)
and
H:Automotive
L:Taping
Characteristics
∗B:Bulk
∗Bulk packing also available. (A product is put in the plastic bag under the taping conditions.)
3. Rating
・Operating Temperature Range
-40 to +125°C
・Storage Temperature Range.
-40 to +125°C
Customer
Part Number
MURATA
Part Number
Inductance
DC
Resistance
(Ω)max.
Self
Resonant
Frequency
(MHz min.)
Rated Current(mA)
ESD Rank
(μH)
(@1MHz)
Tolerance
(%)
∗1
Based on
Inductance
change
∗2
Based on
Temperature rise
Ambient
temperature
85
℃
125
℃
LQW32FT100M0HL 10 M：±20 0.40 100 500 700 140
5B
（12kV(AD) < 16kV(AD)）
LQW32FT220M0HL 22 M：±20 0.62 50 400 550 110
5B
（12kV(AD) < 16kV(AD)）
LQW32FT470M0HL 47 M：±20 0.9 30 300 500 100
5B
（12kV(AD) < 16kV(AD)）
∗1：When applied Rated current to the Products,Inductance will be within ±30% of nominal Inductance value.
∗2：Keep the temperature(ambient temperature plus self-generation of heat) under 125°C.
When rated current is applied to the products, temperature rise caused by self-generated heat shall be limited to
40°C max.
As for the rated current marked with *2, rated current is derated as following figure depending on the operating
temperature.
4. Testing Conditions
《Unless otherwise specified》 《In case of doubt》
Temperature
: Ordinary Temperature / 15°C to 35°C Temperature : 20°C±2°C
Humidity
: Ordinary Humidity / 25%(RH) to 85%(RH) Humidity : 60%(RH) to 70%(RH)
Atmospheric Pressure
: 86kPa to 106 kPa
SpecNo.JELF243A-9147A-01 P.2/8
MURATA MFG.CO.,LTD
Reference Only
5.
Appearance and Dimensions
■Unit Mass (Typical value)
0.073g
6.Electrical Performance
No. Item Specification Test Method
6.1
Inductance
Inductance shall meet item 3.
Measuring Equipment：KEYSIGHT E4294A or equivalent
Measuring Frequency：<Inductance> 1MHz
6.2 DC Resistance DC Resistance shall meet item 3.
Measuring Equipment：Digital multi meter
6.3 Self Resonant
Frequency
(S.R.F)
S.R.F shall meet item 3.
Measuring Equipment：KEYSIGHT E4294A or equivalent
7. Q200 Requirement
7.1.Performance (based on Table 5 for Magnetics(Inductors / Transformer)
AEC-Q200 Rev.D issued June 1. 2010
AEC-Q200
Murata Specification / Deviation
No Stress Test Method
3 High
Temperature
Exposure
1000hours at 125 deg C
Set for 24hours at room temperature,
then measured.
Meet Table A after testing.
Table A
4 Temperature
Cycling
1000cycles
-40 deg C to +125 deg C
Set for 24hours at room temperature,
then measured.
Meet Table A after testing.
7 Biased Humidity 1000hours at 85 deg C, 85%R.H Meet Table B after testing.
Table B
8 Operational Life Apply Rated Current (at 125 deg C)
125 deg C 1000hours
Set for 24hours at room temperature,
then measured
Meet Table B after testing.
9 External Visual Visual inspection
No abnormalities
Appearance No damage
Inductance change
(at 1MHz)
Within ±10%
Appearance No damage
Inductance change
(at 1MHz)
Within ±20%
SpecNo.JELF243A-9147A-01 P.3/8
MURATA MFG.CO.,LTD
Reference Only
AEC-Q200
Murata Specification / Deviation
No Stress Test Method
10 Physical
Dimension
Meet ITEM 5
(Style and Dimensions)
No defects
12 Resistance
to Solvents
Per
MIL-STD-202
Method 215
Not Applicable
13 Mechanical Shock
Per MIL-STD-202
Method 213
Condition C：100g’s(0.98N), 6ms,
Half sine, 12.3ft/s
Meet Table A after testing.
14 Vibration 5g's(0.049N) for 20 minutes,
12cycles each of 3 orientations
Test from 10-2000Hz.
Meet Table A after testing.
15 Resistance
to Soldering Heat
No-heating
Solder temperature 260C+/-5 deg C
Immersion time 10s
Pre-heating：150 to 180C / 90±30s
Meet Table A after testing.
17 ESD
Per AEC-Q200-002
ESD Rank：Refer to Item 3. Rating.
Meet Table A after testing
18 Solderbility Per J-STD-002
Method b：Not Applicable
95% of the terminations is to be soldered.
(Except exposed wire)
19 Electrical
Characterization
Measured：Inductance
No defects
20 Flammability Per UL-94 Not Applicable
21 Board Flex Epoxy-PCB(1.6mm)
Deflection 2mm(min)
Holding time 60s
Meet Table C after testing.
Table C
22 Terminal Strength Per AEC-Q200-006
A force of 17.7N for 60s
No defect
8. Specification of Packaging
8.1 Appearance and Dimensions of plastic tape (12mm-wide, 4mm pitch)
Dimension of the Cavity is measured at the bottom side.
Appearance No damage
DC resistance change Within ±10%
P1-P3P4-P6P7-P8

LQW32FT100M0HL

Mfr. #:
Buy LQW32FT100M0HL
Manufacturer:
Murata Electronics
Description:
Fixed Inductors 1210 47uH 500mA 500mA AEC-Q200
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet