62
Switching Power Supply S82K
Specifications Table PFC Models (S82K-Pjjj24) – continued from previous page
Item
Single output
Power Rating 90 W 100 W 240 W
Characteristics
Ambient temperature
Operating See the derating curve in the Engineering Data section (no condensation or icing)
Storage –25qC to 65qC (no condensation or icing)
Ambient humidity
Operating 25% to 85%
Storage 25% to 90%
Dielectric strength 3,000 VAC at 50/60 Hz for 1 min. (between all inputs and outputs)
2,000 VAC at 50/60 Hz for 1 min. (between all inputs and GR terminal)
1,000 VAC at 50/60 Hz for 1 min. (between all outputs and GR terminal)
Alarm current: 20 mA (90- and 100-W models) 25 mA (240-W models)
Insulation resistance 100 M: min. at 500 VDC (between all outputs and all inputs/GR terminal)
Vibration resistance Malfunction:10 to 55 Hz, 0.375-mm single
amplitude for 2 hrs each in X, Y,
and Z directions
Malfunction:10 to 55 Hz, 0.15-mm
single amplitude for 2 hrs
each in X, Y, and Z
directions
Shock resistance Malfunction:150 m/s
2
, 3 times each in rX,
rY, and rZ directions
Malfunction:300 m/s
2
, 3 times each in
rX, rY, and rZ directions
Screw tightening torque
0.74 N S m max. (See Note 2.)
Output indicator Yes (Green)
Electromagnetic interference
(See Note 1.)
Conforms to FCC class A
EMC (See Notes 3, 4.) 90-, 100-W Models
(EMI): EN50081-1
Harmonic Current: EN61000-3-2 (200 VAC input only)
Emission Enclosure: EN55022 class B
Emission AC Mains: EN55022 class B
Emission Output Ports: EN55022 class A (with a recommended optional filter) (See
Note 3.)
240-W Model
(EMI): EN50081-2
Harmonic Current: EN61000-3-2
Emission Enclosure: EN55011 class A (See Note 4.)
Emission AC Mains: EN55011 class A
Common to All Models
(EMS): EN50082-2
Immunity ESD: EN61000-4-2: 4-kV contact discharge (level 2)
8-kV air discharge (level 3)
Immunity Burst: EN61000-4-4: 2-kV power-line (level 3)
2-kV output line (level 4)
Immunity Surge: EN61000-4-5: between 2-kV lines (except for 240-W
models)
between 4-kV line and FG (except for
240-W models)
Approved standards UL508 (Listing)/1950
Class 2 (UL1310)/Class 2 (CSA C22.2 No.
950) (See Note 5.)
CSA C22.2 No. 14/No. 950, EN50178
(VDE160), EN60950
Conforms to VDE0106/P100
UL508 (Listing)/1012
CSA C22.2 No. 14/E.B. 1402C,
EN50178 (VDE160), EN60950,
Conforms to VDE0106/P100
Weight 1,000 g max. 2,200 g max.
(The notes below apply to this page only.)
Note: 1. Defined with a 100% load and the rated input voltage (100 or 200 VAC)
2. Do not press down on the terminal block with a force exceeding 75 N while tightening the terminals.
3. To ensure the Emission Enclosure ratings, a noise filter should be used on the output lines at the closest point. (90- and 100-W
models: S82Y-JF6-N)
4. To ensure the Emission Enclosure rating, a ferrite ring core should be used on all cables.
5. To meet Class-2 requirements with the 100-W model, either a fuse or circuit breaker that is UL listed or CSA certified, and rated
at 4.2 A max. should be used in the output of the power supply. Only then can the power supply output be considered as meet-
ing Class 2.
