© PHOENIX CONTACT - 08/2005
Data Sheet
AUTOMATIONWORX
7181_en_00 1
PHOENIX CONTACT GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany
Phone: +49-(0) 5235-3-00 • Fax: +49-(0) 5235-3-4 12 00 • www.phoenixcontact.com
www.phoenixcontact.com/salesnetwork
IBS IL 24 RB-LK (-2MBD)
Description
The branch terminal is designed for use within an Inline
station. The terminal offers the possibility of expanding the
INTERBUS network by additional system levels. In total up
to 15 levels can be operated in the network.
Snapping on the branch terminal to an INTERBUS bus
coupler, a control terminal or a branch terminal opens a
remote bus branch at this preconnected terminal. The
IBS IL 24 RB-LK (-2MBD) terminal is the first terminal in the
remote bus branch.
The branch terminal has an outgoing fiber optic remote bus
interface and a combined remote bus branch/local bus
interface (Inline data jumper) additionally. If an additional
branch terminal (IBS IL 24 RB-LK or IBS IL 24 RB-T) is
snapped onto this interface, it opens a remote bus branch.
If any other device is snapped on, the interface opens a
local bus.
The functions of the IBS IL 24 RB-LK and
IBS IL 24 RB-LK-2MBD terminals are identical. The
essential difference between them is the transmission
speed.
Further differing technical data are particularly identified.
For greater clarity, the designation IBS IL 24 RB-LK is used
throughout this document.
IBS IL 24 RB-LK: 500 kBaud
IBS IL 24 RB-LK-2MBD: 2 MBaud
L
D
LD
R
B
-
L
K
RB-LK
R
D
RD
R
C
RC
D
F
O
FO
O
U
T
X
1
X
2
This data sheet is only valid in association with the "Configuring and Installing the INTERBUS Inline Product
Range" user manual IB IL SYS PRO UM E.
Please note the "Configuration Notes" on page 5 to avoid configuration errors.
Make sure you always use the latest documentation.
It can be downloaded at www.download.phoenixcontact.com
.
A conversion table is available on the Internet at
www.download.phoenixcontact.com/general/7000_en_00.pdf.
This data sheet is valid for the terminals listed under "Ordering Data" on page 11.
Inline Branch Terminal
for an INTERBUS Remote Bus;
Connections Using Fiber Optics
IBS IL 24 RB-LK (-2MBD)
7181_en_00 PHOENIX CONTACT 2
Local Diagnostic and Status Indicators and Remote Bus Connections
Figure 1 Local diagnostic and status indicators and
remote bus connections
Local Diagnostic Indicators
RD ON: The fiber optic remote bus is disabled.
Possible causes:
This interface or a preconnected interface has been
switched off.
INTERBUS is not running
(is not in the RUN state).
Remote Bus Connections
Function Identification
Gray
2 MBaud: white stripe in the vicinity of the D LED
OUT
IN
LD
RB-LK
RD
RC
D
FO
7181A002
X1
X2
Des. Color Meaning
D Green Diagnostics
RC Green Remote bus cable check
RD Yellow Remote bus disabled
LD Yellow Remote bus branch/local bus
disconnected
LD Red Isolated disconnection of remote bus
branch/local bus disconnected after error
FO Yellow Status of the outgoing fiber optic path
If, in the event of an error, the preconnected
bus terminal disconnects its remote bus
branch/local bus interface in isolation, the RD
and LD LEDs light up on this RB-LK.
For the function description of all other LEDs,
please refer to the "Configuring and Installing
the INTERBUS Inline Product Range" user
manual.
Designation Connection
X1 OUT Transmit data of outgoing remote bus
X2 IN Receive data of outgoing remote bus
IBS IL 24 RB-LK (-2MBD)
7181_en_00 PHOENIX CONTACT 3
Connecting the Remote Bus Cables
Figure 2 Connecting the remote bus cables
Connect the fiber optic remote bus cable to the terminal
using F-SMA connectors.
Fit the corresponding F-SMA connectors to the fiber
optic cables.
Place the connectors into the appropriate connections.
Secure the connections with the cap nuts.
Internal Circuit Diagram
Figure 3 Internal circuit diagram
Please refer to the Fiber Optic Installation
Guidelines DB EN IBS SYS FOC ASSEMBLY
(Part No. 94 23 43 9) when assembling optical
fibers.
The label for the fiber optic connections (black/
orange) corresponds to the color of the fiber
optics for the polymer fiber cable, which are
specified under "Fiber Optic Interface" on
page 10.
Connect the individual fiber optic cables
between adjacent terminals according to their
color (e.g., orange cable to orange
connections).
A
B
Key:
LED
INTERBUS protocol chip (bus logic
including voltage conditioning)
Fiber optic connections
Power supply unit with electrical isolation
Other symbols used are explained in the
IB IL SYS PRO UM E user manual.
INTERBUS
+U
L
+24V (U )
S
+24V (U )
M
U
ANA
LGND
X1 OUT
X2 IN
AGND
FE
24 V
5V
Sµpi3
OPC
7181A004
Sµpi3
OPC
OUT
IN

2878117

Mfr. #:
Manufacturer:
Phoenix Contact
Description:
I/O Modules IBS IL 24 RB-LK
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet