4
AT28C010 Military
Atmel-0010I-PEEPR-AT28C010-Datasheet_062015
Once set, SDP will remain active unless the disable command sequence is issued. Power transi-
tions do not disable SDP and SDP will protect the AT28C010 during power-up and power-down
conditions. All command sequences must conform to the page write timing specifications. The
data in the enable and disable command sequences is not written to the device and the memory
addresses used in the sequence may be written with data in either a byte or page write opera-
tion.
After setting SDP, any attempt to write to the device without the 3-byte command sequence will
start the internal write timers. No data will be written to the device; however, for the duration of
t
WC
, read operations will effectively be polling operations.
DEVICE IDENTIFICATION: An extra 128-bytes of EEPROM memory are available to the user
for device identification. By raising A9 to 12V 0.5V and using address locations 1FF80H to
1FFFFH the bytes may be written to or read from in the same manner as the regular memory
array.
OPTIONAL CHIP ERASE MODE: The entire device can be erased using a 6-byte software
code. Please see Software Chip Erase application note for details.
Notes: 1. X can be VIL or VIH.
2. Refer to AC Programming Waveforms
DC and AC Operating Range
AT28C010-12 AT28C010-15 AT28C010-20 AT28C010-25
Operating
Temperature (Case)
Mil. -55°C - 125°C -55°C - 125°C -55°C - 125°C -55°C - 125°C
V
CC
Power Supply 5V 10% 5V 10% 5V 10% 5V 10%
Operating Modes
Mode CE OE WE I/O
Read V
IL
V
IL
V
IH
D
OUT
Write
(2)
V
IL
V
IH
V
IL
D
IN
Standby/Write Inhibit V
IH
X
(1)
XHighZ
Write Inhibit X X V
IH
Write Inhibit X V
IL
X
Output Disable X V
IH
XHighZ
DC Characteristics
Symbol Parameter Condition Min Max Units
I
LI
Input Load Current V
IN
=0VtoV
CC
+1V 10 A
I
LO
Output Leakage Current V
I/O
=0VtoV
CC
10 A
I
SB1
V
CC
Standby Current CMOS CE = V
CC
-0.3VtoV
CC
+ 1V 300 A
I
SB2
V
CC
Standby Current TTL CE = 2.0V to V
CC
+1V 3 mA
I
CC
V
CC
Active Current f = 5 MHz; I
OUT
=0mA 80 mA
V
IL
Input Low Voltage 0.8 V
5
AT28C010 Military
Atmel-0010I-PEEPR-AT28C010-Datasheet_062015
AC Read Waveforms
(1)(2)(3)(4)
Notes: 1. CE may be delayed up to t
ACC
-t
CE
after the address transition without impact on t
ACC
.
2.
OE may be delayed up to t
CE
-t
OE
after the falling edge of CE without impact on t
CE
or by t
ACC
-
t
OE
after an address change without impact in t
ACC
.
3. t
DF
is specified from OE or CE wichever occurs first (CL = 5 pF).
4. This parameter is characterized and is not 100% tested.
5. If CE is de-asserted, it must remain de-asserted for at least 50ns during read operations other-
wise incorrect data may be read.
V
IH
Input High Voltage 2.0 V
V
OL
Output Low Voltage I
OL
= 2.1 mA 0.45 V
V
OH1
Output High Voltage I
OH
= -400 A 2.4 V
V
OH2
Output High Voltage CMOS I
OH
= -100 A; V
CC
= 4.5V 4,2 V
DC Characteristics (Continued)
Symbol Parameter Condition Min Max Units
AC Read Characteristics
Symbol Parameter
AT28C010-12 AT28C010-15 AT28C010-20 AT28C010-25
UnitsMin Max Min Max Min Max Min Max
t
ACC
Address to Output Delay 120 150 200 250 ns
t
CE
(1)
CE to Output Delay 120 150 200 250 ns
t
OE
(2)
OE to Output Delay 0 50 0 55 0 55 0 55 ns
t
DF
(3, 4)
CE or OE to Output Float 0 50 0 55 0 55 0 55 ns
t
OH
Output Hold from OE, CE or
Address, whichever occurred first
0000ns
t
CEPH
(5)
CE Pulse High Time 50 50 50 50 ns
6
AT28C010 Military
Atmel-0010I-PEEPR-AT28C010-Datasheet_062015
Input Test Waveforms and
Measurement Level
Output Test Load
Note: 1. This parameter is 100% characterized and is not 100% tested.
Pin Capacitance
f = 1 MHz, T = 25°C
(1)
Symbol Typ Max Units Conditions
C
IN
410pFV
IN
=0V
C
OUT
812pFV
OUT
=0V
AC Write Characteristics
Symbol Parameter Min Max Units
t
WC
Write Cycle Time 10 ms
t
AS
Address Set-up Time 0 ns
t
AH
Address Hold Time 50 ns
t
DS
Data Set-up Time 50 ns
t
DH
Data Hold Time 0 ns
t
WP
Write Pulse Width 100 ns
t
BLC
Byte Load Cycle Time 150 s
t
WPH
Write Pulse Width High 50 ns

AT28C010-25FM/883

Mfr. #:
Manufacturer:
Microchip Technology / Atmel
Description:
EEPROM 1M 5V SDP - 250NS
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union