2.3. ATtiny9
Supply Voltage Speed
(1)
Temperature Package
(2)
Ordering Code
(3)
1.8 – 5.5V 12MHz
Industrial
(-40°C to 85°C)
(4)
6ST1 ATTINY9-TSUR
(5)
ATTINY9-TSHR
(6)(7)
8MA4 ATTINY9-MAHR
(7)
10MHz
Extended
(-40°C to 125°C)
(8)
6ST1 ATTINY9-TSFR
(5)
ATTINY9-TS8R
(6)(7)
Note: 
1. For speed vs. supply voltage, see section Speed.
2. All packages are Pb-free, halide-free and fully green and they comply with the European directive
for Restriction of Hazardous Substances (RoHS). NiPdAu finish.
3. Tape and reel.
4. Can also be supplied in wafer form. Contact your local sales office for ordering information and
minimum quantities.
5. Marking details:
Top mark 1st line: ddddTY
Top mark 2nd line: wwxxx
dddd= device, special code
T= Type
Y= Year last digit
ww= calendar workweek
xxx = trace code
6. Not recommended for new designs.TPUBSTINY-216
7. Top/bottomside markings:
Top: T9x, where x = die revision
Bottom: zHzzz or z8zzz, where H = (-40°C to 85°C), and 8 = (-40°C to 125°C)
8. For typical and Electrical characteristics for this device please consult Appendix A, ATtiny4/5/9/10
Specification at 125°C.
Table 2-3. Package Type
6ST1 6-lead, 2.90 x 1.60 mm Plastic Small Outline Package (SOT23)
8MA4 8-pad, 2 x 2 x 0.6 mm Plastic Ultra Thin Dual Flat No Lead (UDFN)
Atmel ATtiny4 / ATtiny5 / ATtiny9 / ATiny10 [DATASHEET]
Atmel-8127H-ATiny4/ ATiny5 /ATiny9/ ATiny10_Datasheet_Summary-11/2016
7
2.4. ATtiny10
Supply Voltage Speed
(1)
Temperature Package
(2)
Ordering Code
(3)
1.8 – 5.5V 12MHz
Industrial
(-40°C to 85°C)
(4)
6ST1 ATTINY10-TSUR
(5)
ATTINY10-TSHR
(6)(7)
8MA4 ATTINY10-MAHR
(7)
10MHz
Extended
(-40°C to 125°C)
(8)
6ST1 ATTINY10-TSFR
(5)
ATTINY10-TS8R
(6)(7)
Note: 
1. For speed vs. supply voltage, see section Speed.
2. All packages are Pb-free, halide-free and fully green and they comply with the European directive
for Restriction of Hazardous Substances (RoHS). NiPdAu finish.
3. Tape and reel.
4. Can also be supplied in wafer form. Contact your local sales office for ordering information and
minimum quantities.
5. Marking details:
Top mark 1st line: ddddTY
Top mark 2nd line: wwxxx
dddd= device, special code
T= Type
Y= Year last digit
ww= calendar workweek
xxx = trace code
6. Not recommended for new designs.TPUBSTINY-216
7. Top/bottomside markings:
Top: T10x, where x = die revision
Bottom: zHzzz or z8zzz, where H = (-40°C to 85°C), and 8 = (-40°C to 125°C)
8. For typical and Electrical characteristics for this device please consult Appendix A, ATtiny4/5/9/10
Specification at 125°C.
Table 2-4. Package Type
6ST1 6-lead, 2.90 x 1.60 mm Plastic Small Outline Package (SOT23)
8MA4 8-pad, 2 x 2 x 0.6 mm Plastic Ultra Thin Dual Flat No Lead (UDFN)
Atmel ATtiny4 / ATtiny5 / ATtiny9 / ATiny10 [DATASHEET]
Atmel-8127H-ATiny4/ ATiny5 /ATiny9/ ATiny10_Datasheet_Summary-11/2016
8
3. Overview
This device is low-power CMOS 8-bit microcontrollers based on the compact AVR enhanced RISC
architecture. By executing powerful instructions in a single clock cycle, the device achieve throughputs
approaching 1 MIPS per MHz, allowing the system designer to optimize power consumption versus
processing speed.
3.1. Block Diagram
Figure 3-1. Block Diagram
CPU
ADC[7:0]
Vcc
I/O
PORTS
D
A
T
A
B
U
S
SRAM
FLASH
AC
AIN0
AIN1
ACO
ADCMUX
Watchdog
Timer
Power
management
and clock
control
Vcc
GND
Power
Supervision
POR & RESET
RESET
PCINT[3:0]
INT0
Interrupt
Clock generation
128 kHz Internal Osc
External clock
8MHz Calib Osc
PB[3:0]
Internal
Reference
ADC
TC 0
(16-bit)
OC0A/B
T0
ICP0
3.1.1. Description
The AVR core combines a rich instruction set with 16 general purpose working registers and system
registers. All registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent
registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture
is compact and code efficient while achieving throughputs up to ten times faster than conventional CISC
microcontrollers.
This device provides the following features: 512/1024 byte of In-System Programmable Flash, 32 bytes of
SRAM, four general purpose I/O lines, 16 general purpose working registers, a 16-bit timer/counter with
two PWM channels, internal and external interrupts, a programmable watchdog timer with internal
oscillator, an internal calibrated oscillator, and four software selectable power saving modes. ATtiny5/10
are also equipped with a four-channel and 8-bit Analog to Digital Converter (ADC).
Idle mode stops the CPU while allowing the SRAM, timer/counter, ADC (ATtiny5/10, only), analog
comparator, and interrupt system to continue functioning. ADC Noise Reduction mode minimizes
switching noise during ADC conversions by stopping the CPU and all I/O modules except the ADC. In
Power-down mode registers keep their contents and all chip functions are disabled until the next interrupt
Atmel ATtiny4 / ATtiny5 / ATtiny9 / ATiny10 [DATASHEET]
Atmel-8127H-ATiny4/ ATiny5 /ATiny9/ ATiny10_Datasheet_Summary-11/2016
9

ATTINY4-TS8R

Mfr. #:
Manufacturer:
Microchip Technology / Atmel
Description:
8-bit Microcontrollers - MCU 512B FLASH 32B SRAM TIMER
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union