ADG711BRUZ-REEL Datasheet ADG711BRUZ-REEL, ADG711BRUZ, ADG712BRUZ | P4-P6

ADG711/ADG712/ADG713

Rev. B | Page 4 of 16

V

DD

= +3 V ± 10%, GND = 0 V. All specifications −40°C to +85°C, unless otherwise noted.

Table 2.

Parameter +25°C −40°C to +85°C Unit Test Conditions/Comments

ANALOG SWITCH

Analog Signal Range 0 V to V

DD

V

On Resistance (R

ON

) 5 5.5 Ω typ V

S

= 0 V to V

DD

, I

S

= −10 mA;

8 Ω max See Figure 11

On Resistance Match Between 0.1 Ω typ V

S

= 0 V to V

DD

, I

S

= −10 mA

Channels (ΔR

ON

) 0.3 Ω max

On Resistance Flatness (R

FLAT(ON)

) 2.5 Ω typ V

S

= 0 V to V

DD

, I

S

= −10 mA

LEAKAGE CURRENTS V

DD

= +3.3 V

Source Off Leakage I

S

(Off) ±0.01 nA typ V

S

= 3 V/1 V, V

D

= 1 V/3 V

±0.1 ±0.2 nA max See Figure 12

Drain Off Leakage I

D

(Off) ±0.01 nA typ V

S

= 3 V/1 V, V

D

= 1 V/ 3 V

±0.1 ±0.2 nA max See Figure 12

Channel On Leakage I

D

, I

S

(On) ±0.01 nA typ V

S

= V

D

= 1 V, or 3 V

±0.1 ±0.2 nA max See Figure 13

DIGITAL INPUTS

Input High Voltage, V

INH

2.0 V min

Input Low Voltage, V

INL

0.4 V max

Input Current

I

INL

or I

INH

0.005 μA typ V

IN

= V

INL

or V

INH

±0.1 μA max

DYNAMIC CHARACTERISTICS

1

t

ON

13 ns typ R

L

= 300 Ω, C

L

= 35 pF

20 ns max V

S

= 2 V; see Figure 14

t

OFF

7 ns typ R

L

= 300 Ω, C

L

= 35 pF

12 ns max V

S

= 2 V; see Figure 14

Break-Before-Make Time Delay, t

D

7 ns typ R

L

= 300 Ω, C

L

= 35 pF

(ADG713 Only) 1 ns min V

S1

= V

S2

= 2 V; see Figure 15

Charge Injection 3 pC typ V

S

= 1.5 V; R

S

= 0 Ω, C

L

= 1 nF; see Figure 16

Off Isolation −58 dB typ R

L

= 50 Ω, C

L

= 5 pF, f = 10 MHz

−78 dB typ R

L

= 50 Ω, C

L

= 5 pF, f = 1 MHz; see Figure 17

Channel-to-Channel Crosstalk −90 dB typ R

L

= 50 Ω, C

L

= 5 pF, f = 10 MHz; see Figure 18

Bandwidth −3 dB 200 MHz typ R

L

= 50 Ω, C

L

= 5 pF; see Figure 19

C

S

10 pF typ

C

D

10 pF typ

C

D

, C

S

(On) 22 pF typ

POWER REQUIREMENTS V

DD

= +3.3 V

I

DD

0.001 μA typ Digital inputs = 0 V or 3 V

1.0 μ max

1

Guaranteed by design, not subject to production test.

ADG711/ADG712/ADG713

Rev. B | Page 5 of 16

ABSOLUTE MAXIMUM RATINGS

T

A

= +25°C, unless otherwise noted.

Table 3.

Parameter Rating

V

DD

to GND −0.3 V to +6 V

Analog, Digital Inputs

1

−0.3 V to V

DD

+0.3 V or

30 mA, whichever occurs

first

Continuous Current, S or D 30 mA

Peak Current, S or D

100 mA (Pulsed at 1 ms,

10% duty cycle maximum)

Operating Temperature Range −40°C to +85°C

Storage Temperature Range −65°C to +150°C

Junction Temperature 150°C

TSSOP Package, Power Dissipation 430 mW

θ

JA

Thermal Impedance 150°C/W

θ

JC

Thermal Impedance 27°C/W

SOIC Package, Power Dissipation 520 mW

θ

JA

Thermal Impedance 125°C/W

θ

JC

Thermal Impedance 42°C/W

Lead Temperature, Soldering

Vapor Phase (60 sec) 215°C

Infrared (15 sec) 220°C

Soldering(Pb-Free)

Reflow, Peak Temperature 260(+0/−5)°C

Time at Peak Temperature 20 sec to 40 sec

ESD 2 kV

Stresses above those listed under Absolute Maximum Ratings

may cause permanent damage to the device. This is a stress

rating only; functional operation of the device at these or any

other conditions above those indicated in the operational

section of this specification is not implied. Exposure to absolute

maximum rating conditions for extended periods may affect

device reliability.

Only one absolute maximum rating may be applied at any

one time.

ESD CAUTION

1

Overvoltages at IN, S or D will be clamped by internal diodes. Currents

should be limited to the maximum ratings given.

ADG711/ADG712/ADG713

Rev. B | Page 6 of 16

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

IN1 1

D1

2

S1

3

NC

4

IN216

D2

15

S2

14

V

DD

13

GND

5

NC

12

S4

6

S3

11

D4

7

D3

10

IN4 8 IN39

NOTES

1. NC = NO CONNECT. DO NOT

CONNECT TO THIS PIN.

ADG711/

ADG712/

ADG713

TOP VIEW

(Not to Scale)

00042-004

Figure 2. Pin Configuration

Table 4.

Pin Number Mnemonic Description

1 IN1 Digital Control Input. Its logic state controls the status of the Switch S1-D1.

2 D1 Drain Pin. Can be used as input or output.

3 S1 Source Pin. Can be used as input or output.

4 NC Not internally connected.

5 GND The most negative power supply pin.

6 S4 Source Pin. Can be used as input or output.

7 D4 Drain Pin. Can be used as input or output.

8 IN4 Digital Control Input. Its logic state controls the status of the Switch S4-D4.

9 IN3 Digital Control Input. Its logic state controls the status of the Switch S3-D3.

10 D3 Drain Pin. Can be used as input or output.

11 S3 Source Pin. Can be used as input or output.

12 NC Not internally connected.

13 V

DD

The most positive power supply pin.

14 S2 Source Pin. Can be used as input or output.

15 D2 Drain Pin. Can be used as input or output.

16 IN2 Digital Control Input. Its logic state controls the status of the Switch S3-D3.

Table 5. Truth Table (ADG711/ADG712)

ADG711 In ADG712 In Switch Condition

0 1 On

1 0 Off

Table 6. Truth Table (ADG713)

Logic Switch 1, 4 Switch 2, 3

0 Off On

1 On Off

ADG711BRUZ-REEL

ADG711BRUZ-REEL

Products related to this Datasheet