OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ACPL-34JT-000E

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16
7
IEC/EN/DIN EN 60747-5-5 Insulation Characteristics
Description Symbol Characteristic Unit
Insulation Classication per DIN VDE 0110/1.89, Table 1
for rated mains voltage ≤ 150Vrms
for rated mains voltage ≤ 300Vrms
for rated mains voltage ≤ 600Vrms
for rated mains voltage ≤ 1000Vrms
I – IV
I – IV
I – IV
I – III
Climatic Classication 40/125/21
Pollution Degree (DIN VDE 0110/1.89) 2
Maximum Working Insulation Voltage V
IORM
1230 V
PEAK
Input to Output Test Voltage, Method b
V
IORM
x 1.875 = V
PR
, 100% Production Test with tm = 1sec,
Partial discharge < 5 pC
V
PR
2306 V
PEAK
Input to Output Test Voltage, Method a
V
IORM
x 1.6 = V
PR
, Type and Sample Test, tm = 10 sec,
Partial Discharge < 5 pC
V
PR
1968 V
PEAK
Highest Allowable Overvoltage (Transient Overvoltage tini = 60 sec) V
IOTM
8000 V
PEAK
Safety-limiting values
– maximum values allowed in the event of a failure (also see Figure 7)
Case Temperature
Input Power
Output Power
T
S
P
S,INPUT
P
S,OUTPUT
175
400
1200
°C
mW
mW
Insulation Resistance at T
S
, V
IO
= 500V R
S
> 10
9
Ohm
Notes:
1. Isolation characteristics are guaranteed only within the safety maximum ratings which must be ensured by protective circuits in application.
Surface mount classication is class A in accordance with CECCOO802.
2. Refer to the optocoupler section of the Isolation and Control Components Designer’s Catalog, under Product Safety Regulation section IEC/EN/DIN
EN 60747-5-5, for a detailed description of Method a and Method b partial discharge test proles.
Figure 7. Dependence of safety limiting values on temperature.
UL
UL 1577, component recognition pro-
gram up to V
ISO
= 5000 V
RMS
expected
prior to product release.
CSA
CSA Component Acceptance Notice
#5, File CA 88324.
IEC/EN/DIN EN 60747-5-5
IEC 60747-5-5
EN 60747-5-5
DIN EN 60747-5-5
The ACPL-34JT is approved by the following organizations:
P
S
– POWER – mW
0
0
T
S
– CASE TEMPERATURE – °C
200
1200
800
25
1400
50 75 100
400
150 175
125
200
600
1000
P
S
, OUTPUT
P
S
, INPUT
8
Insulation and Safety Related Specications
Parameter Symbol Value Units Conditions
Minimum External
Air Gap (Clearance)
L(101) 8.3 mm Measured from input terminals to output terminals,
shortest distance through air.
Minimum External
Tracking (Creepage)
L(102) 8.3 mm Measured from input terminals to output terminals,
shortest distance path along body.
Minimum Internal Plastic
Gap (Internal Clearance)
0.5 mm Through insulation distance conductor to conductor, usually the
straight line distance thickness between the emitter and detector.
Tracking Resistance (Com-
parative Tracking Index)
CTI >175 Volts DIN IEC 112/VDE 0303 Part 1
Isolation Group IIIa Material Group (DIN VDE 0110)
Absolute Maximum Ratings
Parameter Symbol Min. Max. Units Note
Storage Temperature T
S
-55 150 °C
Operating Temperature T
A
-40 125 °C
IC Junction Temperature T
J
150 °C 1
Average Input Current I
F(AVG)
20 mA
Peak Transient Input Current
(<1us pulse width, 300pps)
I
F(TRAN)
1 A
Reverse Input Voltage V
R
6 V
Peak Output Current |I
O(peak)
| 2.5 A 2
Fault Output Current (Sinking) I
FAULT
10 mA
Fault Pin Voltage V
FAULT
-0.5 6 V
UVLO Output Current (Sinking) I
UVLO
10 mA
UVLO Pin Voltage V
UVLO
-0.5 6 V
Positive Input Supply Voltage V
CC1
-0.5 26 V
Total Output Supply Voltage V
CC2
- V
EE2
-0.5 30 V
Negative Output Supply Voltage V
E
- V
EE2
-0.5 15 V 3
Positive Output Supply Voltage V
CC2
- V
E
-0.5 30 V
Gate Drive Output Voltage Vo(peak) -0.5 V
CC2
+ 0.5 V
Peak Clamping Sinking Current I
CLAMP
2 A 2
Miller Clamping Pin Voltage V
CLAMP
- V
EE2
-0.5 V
CC2
V
DESAT Voltage V
DESAT
- V
E
VE – 0.5 V
CC2
+ 0.5 V 4
Output IC Power Dissipation P
O
580 mW 1
Input IC Power Dissipation P
I
150 mW
Recommended Operating Conditions
Parameter Symbol Min. Max. Units Notes
Operating Temperature T
A
-40 125 °C
Input Supply Voltage V
CC1
8 18 Volts 5
Total Output Supply Voltage V
CC2
- V
EE2
15 25 V 6
Negative Output Supply Voltage V
E
- V
EE2
0 10 V 3
Positive Output Supply Voltage V
CC2
- V
E
15 25 V
Input LED Current I
F(ON)
10 16 mA
Input Voltage (OFF) V
F(OFF)
-3.6 0.8 V
Input pulse width t
ON(LED)
500 ns
9
Electrical Specications
Unless otherwise specied, all Minimum/Maximum specications are at recommended operating conditions, all volt-
ages at input IC are referenced to V
EE1
, all voltages at output IC referenced to V
EE2
. All typical values at T
A
= 25 °C, V
CC1
=
12 V, V
CC2
-V
EE2
= 20 V, V
E
-V
EE2
= 0 V.
Parameter Symbol Min. Typ. Max. Units Test Conditions Fig Note
Input Low Supply Current I
CC1L
3.7 6.0 mA I
F
=0mA 8
Input High Supply Current I
CC1H
3.7 6.0 mA I
F
=10mA 8
Output Low Supply Current I
CC2L
10.5 13.2 mA I
F
=0mA 9
Output High Supply Current I
CC2H
10.6 13.6 mA I
F
=10mA 9
LED Forward Voltage V
F
1.25 1.55 1.85 V I
F
=10mA 10
LED Reverse Breakdown Voltage V
BR
6 V I
F
=10mA
Input Capacitance C
IN
90 pF
LED Turn on Current Threshold
Low to High
I
TH+
2.7 6.6 mA V
O
=5V
LED Turn on Current Threshold
High to Low
I
TH-
2.1 6.4 mA V
O
=5V
LED Turn on Current Hysteresis I
TH_HYS
0.6 mA
High Level Output Current I
OH
-0.75 -2.0 A V
OUT
= V
CC2
- 3 V 11 2
Low Level Output Current I
OL
1.0 2.2 A V
OUT
= V
EE2
+ 2.5 V 12 2
Low Level Soft Shutdown
Current During Fault Condition
I
SSD
22 35 48 mA V
SSD
- V
EE2
= 14V 13
High Level Output Voltage V
OH
VCC2
– 0.5
VCC2
– 0.2
V I
OUT
= -100 mA 11,14 7, 8, 9
Low Level Output Voltage V
OL
0.1 0.5 V I
OUT
= 100 mA 12,15
Clamp Threshold Voltage V
TH_CLAMP
2.0 3.0 V
Clamp Low Level Sinking Current I
CLAMP
0.75 1.9 A V
CLAMP
= V
EE2
+ 2.5
VCC2 UVLO Threshold Low to High V
UVLO+
11.0 12.4 13.7 V V
OUT
> 5 V 9, 10
VCC2 UVLO Threshold High to Low V
UVLO-
10.1 11.3 12.8 V V
OUT
< 5 V 9, 11
VCC2 UVLO Hysteresis V
UVLO_HYS
1.1 V 9
Desat Sensing Threshold V
DESAT
6.2 7.0 7.8 V 16 9
Desat Charging Current I
CHG
0.6 0.9 1.2 mA V
OC
= 2V 17
Desat Discharging Current I
DSCHG
20 53 mA V
OC
= 7V 18
FAULT Logic Low Output Current I
FAULT_L
4.0 9.0 mA V
FAULT
= 0.4V
FAULT Logic High Output Current I
FAULT_H
20 uA V
FAULT
= 5V
UVLO Logic Low Output Current I
UVLO_L
4.0 9.0 mA V
UVLO
= 0.4V
UVLO Logic High Output Current I
UVLO_H
20 uA V
UVLO
= 5V
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P16

ACPL-34JT-000E

Mfr. #:
Buy ACPL-34JT-000E
Manufacturer:
Broadcom / Avago
Description:
High Speed Optocouplers Optocouplers
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet