ST7MDT2-EPB2/US Datasheet ST7MDT1-EPB2/US, ST7MDT2-EPB2/US | P4-P6

Introduction ST7-EPB

4/15 UM0028 Rev 4

About the user manuals...

This manual will help you setup your ST7-EPB programming board and connect it to your PC. Here, you

will find:

■ Setup instructions

■ Information about in-circuit programming connections

For information about the hardware and software intended for use with your programming board, refer to

the following documents that are included with it:

■

ST7 Visual Programmer online help

- program your MCU

■

ST7 Programming Board Descriptions

- a complete list of programming boards, including the

devices and programming modes they support

■

In-Circuit Programming Considerations

- information about setting up your application board for in-

circuit programming

■

ST7xxxx Datasheet

- programming information that is specific to your MCU

Host PC system requirements

Both the hardware and software that you will use to program your ST7 have been designed to operate

with:

■ Microsoft

Windows

2000 or XP

■ Intel

Pentium (or compatible) processor with minimum speed of 133 MHz.

■ Minimum RAM of 32 MB (64 MB recommended).

■ 60 MB of free hard disk space to install all of the ST7 tools.

Note: Windows

2000 and XP

users must have administrator privileges to install STVP7.

Getting assistance

For more information, application notes, FAQs and software updates relevant to all the ST microcontroller

families, check out the CD-ROM or our website:

www.st.com/mcu

For assistance on all ST microcontroller subjects, or for help using your programming board, refer to the

contact list provided in

Product Support

on page 14. We’ll be glad to help you.

ST7-EPB

UM0028 Rev 4 5/15

Contents

1 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.1 Delivery Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.2 Setting up your ST7-EPB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.3 Using the programming sockets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.4 Using an in-circuit programming connection . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.5 Additional information about programming in ISP mode . . . . . . . . . . . . . . . . 10

2 Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.1 Parallel port connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

2.2 About jumpers on the ST7 EPB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Appendix A Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Appendix B Safety Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Appendix C Product Support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

1 Getting Started ST7-EPB

6/15 UM0028 Rev 4

1 Getting Started

Your ST7-EPB programming board is equipped with the sockets you will need to program a

sub-family of ST7 MCUs. In addition, some programming boards also support connections

for In-Circuit Programming (ICP) or In Situ Programming (ISP).

To help you get started programming with your EPB, the following sections provide:

●

Section 1.1

– a checklist of components delivered with your ST7-EPB

●

Section 1.2

– instructions for setting up your programming board

●

Section 1.3

– instructions on the use of programming sockets

●

Section 1.4

– instructions on setting up a connection for in-circuit programming

●

Section 1.5

– additional notes about in situ programming

1.1 Delivery Checklist

The following items are delivered with your programming board (see

Figure 2

1. One ST7MDTxx-EPB programing board.

2. One power supply

3. One parallel cable

Optional

4. One 10-pin, HE-10 type ribbon cable with programming boards that support ICP or ISP

Figure 2. Parts delivered with ST7-EPBs (not to scale)

ST7-EPBs come in several types, which support the programming of different families of ST7 and

package types. The sockets and connectors on your programming board will vary depending on the

type of ST7-EPB you have ordered, and may not correspond exactly to the version shown here.

P1-P3 P4-P6 P7-P9 P10-P12 P13-P15

ST7MDT2-EPB2/US

Mfr. #:

Buy ST7MDT2-EPB2/US

Manufacturer:

STMicroelectronics

Description:

BOARD PROGRAMMING SGL POS ST7

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

ST7MDT2-EPB2/US

ST7MDT2-EPB2/US

Products related to this Datasheet