4
3550.6
February 8, 2006
AC CHARACTERISTICS (A
V
= +2, R
F
= 681)
Slew Rate Note 8 B 25 - 475 - V/s
Full Power Bandwidth Note 9 B 25 - 26 - MHz
Rise Time Note 10 B 25 - 6 - ns
Fall Time Note 10 B 25 - 6 - ns
Propagation Delay Note 10 B 25 - 6 - ns
Overshoot B 25 - 12 - %
-3dB Bandwidth V
OUT
= 100mV B 25 - 95 - MHz
Settling Time to 1% 2V Output Step B 25 - 50 - ns
Settling Time to 0.25% 2V Output Step B 25 - 100 - ns
Gain Flatness 5MHz B 25 - 0.02 - dB
20MHz B 25 - 0.07 - dB
AC CHARACTERISTICS (A
V
= +10, R
F
= 383)
Slew Rate Note 8 B 25 350 475 - V/s
Full Power Bandwidth Note 9 B 25 28 38 - MHz
Rise Time Note 10 B 25 - 8 - ns
Fall Time Note 10 B 25 - 9 - ns
Propagation Delay Note 10 B 25 - 9 - ns
Overshoot B 25 - 1.8 - %
-3dB Bandwidth V
OUT
= 100mV B 25 - 65 - MHz
Settling Time to 1% 2V Output Step B 25 - 75 - ns
Settling Time to 0.1% 2V Output Step B 25 - 130 - ns
VIDEO CHARACTERISTICS
Differential Gain (Note 15) R
L
= 150 B 25 - 0.03 - %
Differential Phase (Note 15) R
L
= 150 B 25 - 0.03 - Degrees
NOTES:
5. V
CM
= 2.5V. At -40°C Product is tested at V
CM
= 2.25V because short test duration does not allow self heating.
6. R
L
= 100, V
IN
= 2.5V. This is the minimum current which must be pulled out of the Disable pin in order to disable the output. The output is
considered disabled when -10mV V
OUT
+10mV.
7. V
IN
= 0V. This is the maximum current that can be pulled out of the Disable pin with the HA5024 remaining enabled. The HA5024 is
considered disabled when the supply current has decreased by at least 0.5mA.
8. V
OUT
switches from -2V to +2V, or from +2V to -2V. Specification is from the 25% to 75% points.
9. .
10. R
L
= 100, V
OUT
= 1V. Measured from 10% to 90% points for rise/fall times; from 50% points of input and output for propagation delay.
11. A. Production Tested; B. Typical or Guaranteed Limit based on characterization; C. Design Typical for information only.
12. V
IN
= +2V, DISABLE = +5V to 0V. Measured from the 50% point of DISABLE to V
OUT
= 0V.
13. V
IN
= +2V, DISABLE = 0V to +5V. Measured from the 50% point of DISABLE to V
OUT
= 2V.
14. V
IN
= 0V, Force V
OUT
from 0V to 2.5V, t
R
= t
F
= 50ns, DISABLE = 0V.
15. Measured with a VM700A video tester using an NTC-7 composite VITS.
16. V
OUT
= 2.5V. At -40°C Product is tested at V
OUT
= 2.25V because short test duration does not allow self heating.
Electrical Specifications V
SUPPLY
= 5V, R
F
= 1k A
V
= +1, R
L
= 400 C
L
10pF,Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
(NOTE 11)
TEST
LEVEL
TEMP.
(°C) MIN TYP MAX UNITS
FPBW
Slew Rate
2V
PEAK
-----------------------------
;V
PEAK
2V==
HA5024
