OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

PR03000201303JAC00

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P20
PR01, PR02, PR03
www.vishay.com
Vishay BCcomponents
Revision: 01-Mar-16
16
Document Number: 28729
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
4.23 Climatic sequence:
4.23.2 2 (Ba) Dry heat 200 °C; 16 h
R
ins min.
: 10
3
M
R
max.
: ± (1.5 % R +0.1)
4.23.3 30 (Db)
Damp heat,
cyclic
55 °C; 24 h;
90 % to 100 % RH; 1 cycle
4.23.4 1 (Aa) Cold -55 °C; 2 h
4.23.5 13 (M) Low air pressure
8.5 kPa; 2 h;
15 °C to 35 °C
4.23.6 30 (Db)
Damp heat,
cyclic
55°C; 5days;
95% to100 %RH; 5 cycles
4.24 78 (Cab)
Damp heat
(steady state)
(40± 2) °C;56days;
(93± 3 )% RH
R
max.
:± (3 %R +0.1)
4.25.1 -
Endurance
(at70 °C)
U= or U = U
max.
;
1.5 h on; 0.5 h off; 70 °C; 1000 h
R
max.
:± (5 %R +0.1)
4.26 - Active flammability Accidental overload test
No damage,
no flamming of gauze cylinder
4.29 45 (Xa)
Component solvent
resistance
Isopropyl alcohol (used in industrial application)
+23 °C; toothbrush method
Marking legible; no visible damage
4.35 - Passive flammability Needle flame test
No ignition of product,
no ignition of under layer
burning time is less than 30 s
TEST PROCEDURES AND REQUIREMENTS
IEC
60115-1
CLAUSE
IEC
60068-2-
TEST
METHOD
TEST PROCEDURE
REQUIREMENTS PERMISSIBLE
CHANGE
(R
max.
)
P
70
x R
PR01, PR02, PR03
www.vishay.com
Vishay BCcomponents
Revision: 01-Mar-16
17
Document Number: 28729
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
DIMENSIONS
Type with straight leads
DIMENSIONS - Straight lead type and relevant physical dimensions; see straight leads outline
TYPE
Ø D
MAX.
(mm)
L
1 MAX.
(mm)
L
2 MAX.
(mm)
TERMINATION WIRE MATERIAL (Cu OR FeCu)
AND WIRE DIAMETER (Ø d)
MASS
(mg)
MATERIAL
Ø d
(mm)
PR01 2.5 6.5 8.0
Cu 0.58 ± 0.05 212
FeCu 0.58 ± 0.05 207
PR02 3.9 10.0 12.0
Cu 0.78 ± 0.05 504
FeCu 0.58 ± 0.05 455
FeCu 0.78 ± 0.05 496
PR03 5.2 16.7 19.5
Cu 0.78 ± 0.05 1192
FeCu 0.58 ± 0.05 1079
FeCu 0.78 ± 0.05 1185
DIMENSIONS - Double kink lead type and relevant physical dimensions; see double kinked outline
TYPE
Ø D
MAX.
(mm)
L
1 MAX.
(mm)
L
2 MAX.
(mm)
TERMINATION WIRE
MATERIAL
(Cu OR FeCu) AND
WIRE DIAMETER (Ø d)
MASS
(mg)
PITCH
(mm)
P
1
(mm)
P
2
(mm)
b
1
(mm)
b
2
(mm)
S
MAX.
(mm)
Ø B
(mm)
MATERIAL
Ø d
(mm)
PR01 2.5 6.5 8.0
Cu
0.58
± 0.05
212 17.8
17.8
± 0.5
17.8
± 3
1.10
+ 0.25 / - 0.20
1.45
+ 0.25 / - 0.20
2
0.8
± 0.07
FeCu
0.58
± 0.05
207 12.5
12.5
± 0.5
12.5
± 3
1.10
+ 0.25 / - 0.20
1.45
+ 0.25 / - 0.20
2
0.8
± 0.07
FeCu
0.58
± 0.05
207 17.8
17.8
± 0.5
17.8
± 3
1.10
+ 0.25 / - 0.20
1.45
+ 0.25 / - 0.20
2
0.8
± 0.07
PR02 3.9 10.0 12.0
Cu
0.78
± 0.05
504 17.8
17.8
± 0.5
17.8
± 3
1.10
+ 0.25 / - 0.20
1.45
+ 0.25 / - 0.20
2
1.0
± 0.07
FeCu
0.58
± 0.05
455 17.8
17.8
± 0.5
17.8
± 3
1.10
+ 0.25 / - 0.20
1.45
+ 0.25 / - 0.20
2
0.8
± 0.07
FeCu
0.78
± 0.05
496 15.0
15.0
± 0.5
15.0
± 3
1.30
+ 0.25 / - 0.20
1.65
+ 0.25 / - 0.20
2
1.0
± 0.07
PR03 5.2 16.7
19.5
Cu
0.78
± 0.05
1192 25.4
25.4
± 0.5
25.4
± 3
1.10
+ 0.25 / - 0.20
1.65
+ 0.25 / - 0.20
2
1.0
± 0.07
FeCu
0.58
± 0.05
1079 25.4
25.4
± 0.5
25.4
± 3
1.10
+ 0.25 / - 0.20
1.65
+ 0.25 / - 0.20
2
1.0
± 0.07
FeCu
0.78
± 0.05
1185 20
22.0
± 0.5
20.0
± 3
1.30
+ 0.25 / - 0.20
2.15
+ 0.25 / - 0.20
2
1.0
± 0.07
L
1
d
D
L
2
Ø D
P
1
± 0.5
S
Ø B
± 0.07
Ø d
b
1
4.5
+ 1
0
b
2
8 + 2
L
1
L
2
P
2
± 3
P
1
± 0.5
Type with double kink Dimensions in millimeters
PR01, PR02, PR03
www.vishay.com
Vishay BCcomponents
Revision: 01-Mar-16
18
Document Number: 28729
For technical questions, contact: filmresistorsleaded@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
PR01, PR02 WITH RADIAL TAPING
PR01 - Height for insertion (max.) = 32 mm
PR02 - Height for insertion (max.) = 29 mm
MARKING
The nominal resistance and tolerance are marked on the resistor using four or five colored bands in accordance with IEC 60062,
marking codes for resistors and capacitors.
P
P
2
W
W
0
D
0
P
1
P
0
L
1
L
F
H
0
H
1
H
α = 30° to 40°
α
α
aa
DIMENSIONS in millimeters
Pitch of components P 12.7 ± 1.0
Feed-hole pitch P
0
12.7 ± 0.2
Feed-hole centre to lead
at topside at the tape
P
1
3.85 ± 0.5
Feed-hole center to body center P
2
6.35 ± 1.0
Lead spacing F 4.8 +0.7/-0
Width of carrier tape W 18.0 ± 0.5
Minimum hold down tape width W
0
5.5
Height for insertion (max.) H1 32
Lead wire clinch height H
0
16.5 ± 0.5
Body to hole center H 19.5 ± 1
Feed-hole diameter D
0
4.0 ± 0.2
Height for cutting (max.) L 11.0
Minimum lead wire (tape portion)
shortest lead
L
1
2.5
P
P
2
W
W
0
D
0
P
1
P
0
L
1
L
F
H
0
H
1
H
α = 30° to 40°
α
α
aa
DIMENSIONS in millimeters
Pitch of components P 12.7 ± 1.0
Feed-hole pitch P
0
12.7 ± 0.2
Feed-hole centre to lead
at topside at the tape
P
1
3.85 ± 0.5
Feed-hole center to body center P
2
6.35 ± 1.0
Lead spacing F 4.8 +0.7/-0
Width of carrier tape W 18.0 ± 0.5
Minimum hold down tape width W
0
5.5
Height for insertion (max.) H1 29
Lead wire clinch height H
0
16.5 ± 0.5
Body to hole center H 19.5 ± 1
Feed-hole diameter D
0
4.0 ± 0.2
Height for cutting (max.) L 11.0
Minimum lead wire (tape portion)
shortest lead
L
1
2.5
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P20

PR03000201303JAC00

Mfr. #:
Buy PR03000201303JAC00
Manufacturer:
Vishay
Description:
Metal Film Resistors - Through Hole 3watts 130Kohms 5%
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet