2810887 Datasheet 2810887 | P7-P9

MCR-C-UI-UI-DCI

100238_de_06 PHOENIX CONTACT 7

9 Installation

The assignment of the connection terminal blocks is shown in

the block diagram. The module can be snapped onto all 35

mm DIN rails according to EN 60715.

Assembly

Position the module with the DIN rail guide on the upper edge

of the DIN rail, and snap it in with a downward motion.

Removing

Pull the snap lever open with the aid of a screwdriver and slide

the module out at the lower edge of the DIN rail.

WARNING:

In potentially explosive areas, snap the module

onto the DIN rail and connect the cables only

when the power is disconnected.

123

MCR -C -UI/UI -DCI

Art.-Nr.:281091

IN U/I

GND 1

OUT I

GND 2

+24VDC

GND 3

APPROBATIONEN /

GND 1

OUT U

POWER

OUT

MCR-C-UI-UI-DCI

POWER

SPAN

ZERO

U/I GND1 GND1

I U GND2

+24V GND3 GND3

Screw Connection

Insert the wires in the corresponding connection terminal

block.

Use a screwdriver to tighten the screw in the opening above

the connection terminal block.

MCR-C-UI-UI-DCI

100238_de_06 PHOENIX CONTACT 8

10 Configuration

HYBRID TV1

PHOENIX CONTACT

DIP 1

DIP 2

If the modules are not configured (all DIP switches set to

pos.0), the module does not have a defined function until the

DIP switches have been set.

DIP switches S1 and S2 specify the combination of input and

output standard signal ranges (see configuration table).

Standard Configuration

"NC" versions (...-NC) have the following standard configura-

tion:

– 0 ... 10 V input

– 0 ... 10 V output

(All DIP switches are set to the "OFF" position)

Opening the Module

Using a screwdriver, release the locked upper housing part

on both sides. The upper housing part and the electronics can

now be pulled out approximately 3 cm.

CAUTION: Electrostatic discharge

The module contains components that can be

damaged or destroyed by electrostatic dischar-

ge. When handling the module, observe the

necessary safety precautions against elec-

trostatic discharge (ESD) according to

EN61340-5-1 and IEC61340-5-1.

11 Adjustment

The "ZERO" potentiometer is used to adjust the zero point of

the module and the "SPAN" potentiometer is used to adjust

the final value. Both potentiometers are located on the top of

the module.

NOTE: Module can become damaged

Before commencing the adjustment process,

observe the warm-up phase of two minutes.

MCR-C-UI-UI-DCI

100238_de_06 PHOENIX CONTACT 9

12 DIP switches

X = ON Input 0 ... 5 V Output 0 ... 10 V Output ±5 V Output ±10 V Output

DIP 1 DIP 2 DIP 2 DIP 2 DIP 2

Input 12345678 12345678910 12345678910 12345678910 12345678910

0 ... 60 mV X XXX X X X XX X X XXX X X X XXX

0 ... 100 mV X X X X X X X X X X X X X X X X X X

0 ... 200 mV X X X X X X X X X X X X X X X X X X

0 ... 300 mV X X X X X X X X X X X X X X X X X X X

0 ... 500 mV X X X X X X X X X X X X X X X X X X

0 ... 1 V X X X X X XX X X XXX X X X XXX

0 ... 2 V X X X X X XX X X XXX X X X XXX

0 ... 2.5 V X X X X X X X X X X X X X X X X X

0 ... 5 V X X X X XX X X XXX X X X XXX

0 ... 10 V X X X X XX X X XXX X X X XXX

0 ... 20 V X X X X XX X X XXX X X X XXX

±60 mV X XXX X X X X XX X X X X XX

±100 mV X X X X X X XX X X X X XX

±200 mV X X X X X X XX X X X X XX

±300 mV XXXXXX XXXX XX XXX

±500 mV X X X X X X XX X X X X XX

±1 V X X X X X XXXX X X XXX

±2 V XX XX X XXXX X X XXX

±2.5 V X X X X X XX X X X X XX

±5 V X X X X X XX X X X X XX

±10 V X X X X X XX X X X X XX

±20 V X X X X X XX X X X X XX

0 ... 5 mA X X XXX X X X XX X X XXX X X X XXX

0 ... 10 mA XX X X X X XX X X XXX X X X XXX

0 ... 20 mA X X X X X X XX X X XXX X X X XXX

±5 mA X X XXX X X X X XX X X X X XX

±10 mA XX X XX X XXXX X X XXX

±20 mA XX X XX X XXXX X X XXX

1 ... 5 V X X X X X X X X X X X

4 ... 20 mA X X X X X X X X X X X X X

X = ON 1 ... 5 V Output 0 ... 5 mA Output 0 ... 10 mA Output 0 ... 20 mA Output 4 ... 20 mA Output

DIP 2DIP 2DIP 2DIP 2DIP 2

Input 12345678910 12345678910 12345678910 12345678910 12345678910

0 ... 60 mV X X X X X X X X X X X X X

0 ... 100 mV X X X X X X X X X X X X X

0 ... 200 mV X X X X X X X X X X X X X

0 ... 300 mV X X X X X X X X X X X X X

0 ... 500 mV X X X X X X X X X X X X X

0 ... 1 V X X X X X X X X X X X X X

0 ... 2 V X X X X X X X X X X X X X

0 ... 2.5 V X X X X X X X X X X X X X

0 ... 5 V X X X X X X X X X X X X X

0 ... 10 V X X X X X X X X X X X X X

0 ... 20 V X X X X X X X X X X X X X

±60 mV X X X X X X X

±100 mV X X X X X X X

±200 mV X X X X X X X

±300 mV X X X X X X X

±500 mV X X X X X X X

±1 V XX X XXXX

±2 V XX X XXXX

±2.5 V XX X XXXX

±5 V XX X XXXX

±10 V XX X XXXX

±20 V XX X XXXX

0 ... 5 mA X X X X X X X X X X X X X

0 ... 10 mA X X X X X X X X X X X X X

0 ... 20 mA X X X X X X X X X X X X X

±5 mA X X X X X X X

±10 mA X X X X X X X

±20 mA X X X X X X X

1 ... 5 V X X X X X X X X

4 ... 20 mA X X X X X X X X

±5 V Output ±10 V Output 1 ... 5 V Output 0 ... 20 mA Output 4 ... 20 mA Output

Constant 10 V 20 V 4 V 18 mA 16 mA

Output final value 5V 10V 5V 20mA 20mA

Adjustment tolerance ±0.5 mV ±0.5 mV ±1 mV ±1 μA±1 μA

P1-P3 P4-P6 P7-P9 P10-P11

2810887

Mfr. #:

Buy 2810887

Manufacturer:

Phoenix Contact

Description:

Terminal Block Interface Modules Signal conditioner MCR-C-UI-UI-450-DCI

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet

2810887