13 / 15
2DM180506CM
■Outline Dimensional Drawing
Note :1.The dimensional tolerance without directions is ± 0.5mm.
Unit:mm
■Product Weight
75g(TYP)
■Recommended Hole Diameter And Land Size
※The round pulling out figure is a pin numbering.
Unit:mm
Component side
TAMURA CORPORATION
Rev.F May, 2016
14 / 15
2DM180506CM
■Recommended Soldering Condition
・Flow soldering condition 255±3℃ Less than 5sec
Temperature of preheating 110℃~130℃
End temperature of preheating 110℃±10℃
・Soldering condition of hand work 350℃(MAX) Less than 4sec
■Storage Conditions
※If you want to use past the long period there is a concern that the solder non-wetting by terminal oxidation to occur.
Therefore, please use from taking enough tests.
■Usage Cautions
Always mount fuse on the plus side of input for ensuring safety because the fuse is not built-in the product.
Please select the fuse considering conditions such as steady current, inrush current, and ambient temperature.
When using a fuse having large rated current or high capacity input electrolytic condenser, by combining
another converter and input line and input electrolytic condenser, fuse may not blow off in the case of abnormality.
Do not combine high voltage line and fuse.
This product is designed to be best when it drives two devices to have the same gate capacitance simultaneously.
Because it leads to the "output unstable" and "output accuracy deterioration".
If you want to use to drive only one of the devices, because of the output voltage accuracy deterioration prevention,
please configure the dummy gate circuit (resistor and capacitor) to consume the equivalent of the power and the drive side.
This product is to transmit the signal of the insulating part by the magnetic coupling.
Therefore, if you use this product in a strong magnetic field in, there is a possibility of malfunction.
In that case, connect the capacitor between the GND terminal of this product and a metal enclosure.
Make sure the rise/fall time of the input signal is 500ns or less.
TAMURA CORPORATION
Rev.F May, 2016
Max Unit Conditions・Note
Storage temperature -25 60 A packing state
Item Min
15 / 15
■Important Notice
The content of this information is subject to change without prior notice for the purpose of improvements, etc.
Ensure that you are in possession of the most up-to-date information when using this product.
The operation examples and circuit examples shown in this information are for reference purposes only, and Tamura Corporation disclaims
all responsibility for any violations of industrial property rights, intellectual property rights and any other rights owned by Tamura Corporation
or third parties that these may entail.
The circuit examples and part constants listed in these specifications are provided as reference for the verification of
characteristics. You are to perform design, verification, and judgment at your own responsibility, taking into account
the various conditions.
Tamura Corporation constantly strives to improve quality and reliability, but malfunction or failures are bound to occur with some
probability in power products. To ensure that failures do not cause accidents resulting in injury or death, fire accidents, social damage,
and so on, you are to thoroughly verify the safety of their designs in devices and/or systems.
This product is intended for use in consumer electronics (electric home appliances, business equipment, Information equipment, communication
terminal equipment, measuring devices, and so on.) If considering use of this product in equipment or devices that require high reliability
(medical devices, transportation equipment, traffic signal control equipment, fire and crime prevention equipment, aeronautics and space
devices, nuclear power control, fuel control, in-vehicle equipment, safety devices, and so on), please consult a Tamura sales representative
in advance. Do not use this product for such applications without written permission from Tamura Corporation.
This product is intended for use in environments where consumer electronics are commonly used.
It is not designed for use in special environments such as listed below, and if such use is considered,
you are to perform thorough safety and reliability checks at your own responsibility.
Use in liquids such as water, oil, chemical solutions, or organic solvents, and use in locations
where the product will be exposed to such liquids.
Use that involves exposure to direct sunlight, outdoor exposure, or dusty conditions.
Use in locations where corrosive gases such as salt air, C12, H2S, NH3, SO2, or NO2, are present.
Use in environments with strong static electricity or electromagnetic radiation.
Use that involves placing inflammable material next to the product.
Use of this product either sealed with a resin filling or coated with resin.
Use of water or a water soluble detergent for flux cleaning.
Use in locations where condensation is liable to occur.
This product is not designed to resist radiation.
This product is not designed to be connected in series or parallel.
Do not operate this product in a series, parallel, or N+1 redundant configuration.
Do not use or otherwise make available the TAMURA products or the technology described in this document for any military purposes,
including without limitation, for the design, development, use, stockpiling or manufacturing of mass destruction weapons
(e.g. nuclear, chemical, or biological weapons or missile technology products).
When exporting and re-exporting the products or technology described in this document, you should comply with the applicable export
control laws and regulations and follow the procedures required by such laws and regulations including, without limitation,
Japan -Foreign Exchange and Foreign Trade Control Law and U.S.- Export Administration Regulations.
The TAMURA products and related technology should not be used for or incorporated into any products or systems whose manufacture,
use, or sale is prohibited under any applicable domestic or foreign laws or regulations.
Please contact your TAMURA sales office for details as to environmental matters such as the RoHS compatibility of product.
Please use TAMURA products in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances,
including without limitation, the EU RoHS Directive.
TAMURA assumes no liability for damages or losses occurring as a result of your noncompliance with applicable laws and regulations.
TAMURAassumes no liability fordamages or lossesincurredbyyouorthirdpartiesasaresultofunauthorizeduseof
TAMURAproducts.
This document and any information herein may not be reproduced in whole or in part without prior written permission from TAMURA.
TAMURA CORPORATION
Rev.F May, 2016

2DM180506CM

Mfr. #:
Manufacturer:
Tamura
Description:
GATE DRIVER
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet