NCP1521B
http://onsemi.com
4
ELECTRICAL CHARACTERISTICS (Typical values are referenced to T
A
= +25°C, Min and Max values are referenced −40°C to +85°C
ambient temperature, unless otherwise noted, operating conditions V
IN
= 3.6 V, V
OUT
= 1.2 V, unless otherwise noted.)
Rating
Pin
Symbol Min Typ Max Unit
TSOP UDFN
VIN PIN
Input Voltage Range
1 3 V
IN
2.7 − 5.5 V
Quiescent Current, PFM No Switching 1 3 I
q
ON
− 30 45 mA
Standby Current, EN Low 1 3 I
q
OFF
− 0.2 1.5 mA
Undervoltage Lockout (V
IN
Falling) 1 3 V
UVLO
2.2 2.4 2.55 V
EN PIN
Positive going Input High Voltage Threshold, EN0 Signal 3 1 V
IH
1.2 − − V
Negative going Input High Voltage Threshold, EN0 Signal 3 1 V
IL
− − 0.4 V
EN High Input Current, EN = 3.6 V 3 1 I
ENH
− 2.0 − mA
OUTPUT
Output Voltage Accuracy (Note 6)
Ambient Temperature
Overtemperature Range
V
OUT
−
−3.0
$1.0
$2.0
−
3.0
%
Feedback Voltage Threshold 4 6 V
FB
− 0.6 − V
Minimum Output Voltage V
OUT
− 0.9 − V
Maximum Output Voltage V
OUT
− 3.3 − V
Maximum Output Voltage for USB or 5 V Rail Powered Applications
Vin from 4.3 V to 5.5 V (Note 7)
V
OUT
− 3.9 −
V
Output Voltage load regulation Overtemperature
I
OUT
= 100 mA to 600 mA
V
OUT
−
−
0.0005
−
−
−
%/mA
Load Transient Response, Rise/Falltime 1 ms
10 mA to 100 mA Load Step
200 mA to 600 mA Load Step
V
OUT
−
−
35
80
−
−
mV
Output Voltage Line Regulation, I
OUT
= 100 mA,
V
IN
= 2.7 V to 5.5 V
V
OUT
− 0.05 −
%
Line Transient Response, I
OUT
= 100 mA,
3.6 V to 3.0 V Line Step (Falltime=50 ms)
V
OUT
− 6 −
mV
PP
Output Voltage Ripple, I
OUT
= 300 mA (PWM Mode) V
OUT
− 2.0 − mV
Output Voltage Ripple, I
OUT
= 0 mA (PFM Mode) V
OUT
− 8.0 − mV
Peak Inductor Current 5 5 I
LIM
− 1200 − mA
Oscillator Frequency 5 5 F
OSC
1.3 1.5 1.8 MHz
Duty Cycle 5 5 − − − 100 %
Soft−Start Time T
START
− 320 500 ms
Thermal Shutdown Threshold T
SD
− 160 − °C
Thermal Shutdown Hysteresis T
SDH
− 25 − °C
POWER SWITCHES
P−Channel On−Resistance RLxH − 400 − mW
N−Channel On−Resistance RLxL − 400 − mW
P−Channel Leakage Current I
LeakH
− 0.05 − mA
N−Channel Leakage Current I
LeakL
− 0.01 − mA
6. The overall output voltage tolerance depends upon the accuracy of the external resistor (R1, R2).
7. Functionality guaranteed per design and characterization, see chapter ”USB or 5 V Rail Powered Applications”.