LQW15CAR14K00D Datasheet LQW15CA1R0K00D, LQW15CA22NK00D, LQW15CAR14J00D | P7-P9

SpecNo.JELF243A-0140A-01 P.7/10

MURATA MFG.CO.,LTD

Reference Only

11.4 Reworking with soldering iron

The following conditions must be strictly followed when using a soldering iron.

Pre-heating 150°C,1 min

Tip temperature 350°C max.

Soldering iron output 80W max.

Tip diameter φ3mm max.

Soldering time 3(+1,-0)s

Time 2 times

Note :Do not directly touch the products with the tip of the soldering iron in order to prevent the

crack on the products due to the thermal shock.

11.5 Solder Volume

・Solder shall be used not to be exceed the upper limits as shown below.

・Accordingly increasing the solder volume, the mechanical stress to Chip is also increased.

Exceeding solder volume may cause the failure of mechanical or electrical performance.

1/2T≦t≦T

T：thickness of product

11.6 Product’s location

The following shall be considered when designing and laying out P.C.B.'s.

(1) P.C.B. shall be designed so that products are not subject to the mechanical stress due to

warping the board.

［Products direction］

Products shall be located in the sideways

direction (Length:a＜b) to the mechanical

stress.

(2) Components location on P.C.B. separation.

It is effective to implement the following measures, to reduce stress in separating the board.

It is best to implement all of the following three measures; however, implement as many measures as possible

to reduce stress.

Contents of Measures Stress Level

(1) Turn the mounting direction of the component parallel to the board separation surface. A > D *1

(2) Add slits in the board separation part. A > B

(3) Keep the mounting position of the component away from the board separation surface. A > C

*1 A > D is valid when stress is added vertically to the perforation as with Hand Separation.

If a Cutting Disc is used, stress will be diagonal to the PCB, therefore A > D is invalid.

〈

Poor example

〉

〈

Good example

〉

Upper Limit

Recommendable(t)

Seam

Slit

Length:a

SpecNo.JELF243A-0140A-01 P.8/10

MURATA MFG.CO.,LTD

Reference Only

(3) Mounting Components Near Screw Holes

When a component is mounted near a screw hole, it may be affected by the board deflection that occurs during

the tightening of the screw. Mount the component in a position as far away from the screw holes as possible.

11.7 Cleaning Conditions

Products shall be cleaned on the following conditions.

(1) Cleaning temperature shall be limited to 60°C max.(40°C max for IPA)

(2) Ultrasonic cleaning shall comply with the following conditions with avoiding the resonance

phenomenon at the mounted products and P.C.B.

Power : 20 W / l max. Frequency : 28kHz to 40kHz Time : 5 min max.

(3) Cleaner

1. Alcohol type cleaner

Isopropyl alcohol (IPA)

2. Aqueous agent

PINE ALPHA ST-100S

(4) There shall be no residual flux and residual cleaner after cleaning.

In the case of using aqueous agent, products shall be dried completely after rinse with de-ionized

water in order to remove the cleaner.

(5) Other cleaning Please contact us.

11.8 Resin coating

The inductance value may change due to high cure-stress of resin to be used for coating/molding products.

An open circuit issue may occur by mechanical stress caused by the resin, amount/cured shape of resin, or

operating condition etc. Some resin contains some impurities or chloride possible to generate chlorine by

hydrolysis under some operating condition may cause corrosion of wire of coil, leading to open circuit.

So, please pay your careful attention when you select resin in case of coating/molding the products with the resin.

Prior to use the coating resin, please make sure no reliability issue is observed by evaluating products

mounted on your board.

11.9 Caution for use

・Sharp material such as a pair of tweezers or other material such as bristles of cleaning brush , shall not be

touched to the winding portion to prevent the breaking of wire.

・Mechanical shock should not be applied to the products mounted on the board to prevent the breaking of the core.

11.10 Notice of product handling at mounting

In some mounting machines,when picking up components support pin pushes up the components from the

bottom of base tape. In this case, please remove the support pin. The support pin may damage the components

and break wire.

In rare case ,the laser recognition can not recognize this component. Please contact us when you use laser

recognition. (There is no problem with the permeation and reflection type.)

11.11 Handling of a substrate

After mounting products on a substrate, do not apply any stress to the product caused by bending or twisting to the

substrate when cropping the substrate, inserting and removing a connector from the substrate or tightening screw

to the substrate.

Excessive mechanical stress may cause cracking in the product.

Bending Twisting

SpecNo.JELF243A-0140A-01 P.9/10

MURATA MFG.CO.,LTD

Reference Only

11.12 Storage and Handing Requirements

(1) Storage period

Use the products within 12 months after delivered.

Solderability should be checked if this period is exceeded.

(2) Storage conditions

・Products should be stored in the warehouse on the following conditions.

Temperature ： -10°C to 40°C

Humidity ： 15% to 85% relative humidity No rapid change on temperature and humidity

・Don't keep products in corrosive gases such as sulfur,chlorine gas or acid, or it may cause

oxidization of electrode, resulting in poor solderability.

・Products should not be stored on bulk packaging condition to prevent the chipping of the

core and the breaking of winding wire caused by the collision between the products.

・Products should be stored on the palette for the prevention of the influence from humidity,

dust and so on.

・Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.

(3) Handling Condition

Care should be taken when transporting or handling product to avoid excessive vibration or

mechanical shock.

12．! Note

(1)Please make sure that your product has been evaluated in view of your specifications with our product being

mounted to your product.

(2)You are requested not to use our product deviating from the reference specifications.

(3)The contents of this reference specification are subject to change without advance notice.

Please approve our product specifications or transact the approval sheet for product specifications before ordering.

P1-P3 P4-P6 P7-P9 P10-P10

LQW15CAR14K00D

Mfr. #:

Buy LQW15CAR14K00D

Manufacturer:

Murata Electronics

Description:

Fixed Inductors 0402 140nH 680mA Tol=+/-10%

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

LQW15CAR14K00D

LQW15CAR14K00D

Products related to this Datasheet