TLP152
3
7.
7.
7.
7. Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, T
Absolute Maximum Ratings (Note) (Unless otherwise specified, T
a
a
a
a
= 25
= 25
= 25
= 25
)
)
)
)
LED
Detector
Common
Characteristics
Input forward current
Peak transient input forward
current
Input reverse voltage
Input power dissipation
Peak high-level output current
Peak low-level output current
Output voltage
Supply voltage
Output power dissipation
Operating temperature
Storage temperature
Lead soldering temperature
Isolation voltage
(T
a
= -40 to 100)
(T
a
= -40 to 100)
(10 s)
AC, 1 min,
R.H. ≤ 60%, T
a
= 25
Symbol
I
F
I
FPT
V
R
P
D
I
OPH
I
OPL
V
O
V
CC
P
O
T
opr
T
stg
T
sol
BV
S
Note
(Note 1)
(Note 2)
(Note 2)
(Note 3)
(Note 4)
Rating
20
1
5
40
-2.5
+2.5
35
35
260
-40 to 100
-55 to 125
260
3750
Unit
mA
A
V
mW
A
V
mW
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Pulse width (PW) ≤ 1 µs, 300 pps
Note 2: Exponential waveform. Pulse width ≤ 0.2 µs, f ≤ 15 kHz, VCC = 20V, Ta = -40 to 100
Exponential waveform. Pulse width ≤ 0.08 µs, f ≤ 25 kHz, VCC = 15V, Ta = -40 to 100
Note 3: ≥ 2 mm below seating plane.
Note 4: This device is considered as a two-terminal device: Pins 1, and 3 are shorted together, and pins 4, 5 and 6
are shorted together.
8.
8.
8.
8. Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Recommended Operating Conditions (Note)
Characteristics
Input on-state current
Input off-state voltage
Peak high-level output current
Peak low-level output current
Operating frequency
Symbol
I
F(ON)
V
F(OFF)
I
OPH
I
OPL
f
Note
(Note 1)
(Note 2)
Min
10
0
Typ.
Max
15
0.8
-2.0
+2.0
250
Unit
mA
V
A
kHz
Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this datasheet should also be considered.
Note: A ceramic capacitor (0.1 µF) should be connected between pin 6 and pin 4 to stabilize the operation of a high-
gain linear amplifier. Otherwise, this photocoupler may not switch properly. The bypass capacitor should be
placed within 1 cm of each pin.
Note 1: The rise and fall times of the input on-current should be less than 0.5 µs.
Note 2: Exponential waveform. I
OPH
≥ -0.65 A (≤ 80 ns), I
OPL
≤ 0.65 A (≤ 80 ns), T
a
= 100, V
CC
= 20V
2012-09-14
Rev.3.0
