4
FN6094.3
November 5, 2004
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7) 25 - 106 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7) 25 - 212 - pF
POWER SUPPLY CHARACTERISTICS
Power Supply Range Full 1.65 3.6 V
Positive Supply Current, I+ V+ = 3.6V, V
IN
= 0V or V+ 25 - - 50 nA
Full - - 750 nA
DIGITAL INPUT CHARACTERISTICS
Input Voltage Low, V
INL
Full - - 0.5 V
Input Voltage High, V
INH
Full 1.4 - - V
Input Current, I
INH
, I
INL
V+ = 3.6V, V
IN
= 0V or V+ (Note 8) Full -0.5 - 0.5 µA
NOTES:
4. V
IN
= input voltage to perform proper function.
5. The algebraic convention, whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
6. Parts are 100% tested at +25°C. Limits across the full temperature range are guaranteed by design and correlation.
7. Flatness is defined as the difference between maximum and minimum value of on-resistance over the specified analog signal range.
8. Guaranteed but not tested.
9. R
ON
matching between channels is calculated by subtracting the channel with the highest max Ron value from the channel with lowest max Ron
value, between NC1 and NC2, NC3 and NC4 or between NO1 and NO2, NO3 and NO4.
Electrical Specifications - 1.8V Supply Test Conditions: V+ = +1.65V to +2V, GND = 0V, V
INH
= 1.0V, V
INL
= 0.4V (Notes 4, 6),
Unless Otherwise Specified
PARAMETER TEST CONDITIONS
TEMP
(°C)
(NOTE 5)
MIN TYP
(NOTE 5)
MAX UNITS
ANALOG SWITCH CHARACTERISTICS
Analog Signal Range, V
ANALOG
Full 0 - V+ V
ON Resistance, R
ON
V+ = 1.8V, I
COM
= 100mA, V
NO
or V
NC
= 0V to V+,
(See Figure 5)
25 - 0.45 0.8 Ω
Full - - 0.85 Ω
DYNAMIC CHARACTERISTICS
Turn-ON Time, t
ON
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF,
(See Figure 1, Note 8)
25 - 18 23 ns
Full - - 25 ns
Turn-OFF Time, t
OFF
V+ = 1.65V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF,
(See Figure 1, Note 8)
25 - 10 15 ns
Full - - 18 ns
Break-Before-Make Time Delay, t
D
V+ = 2.0V, V
NO
or V
NC
= 1.0V, R
L
= 50Ω, C
L
= 35pF,
(See Figure 3, Note 8)
Full 2 5 - ns
Charge Injection, Q C
L
= 1.0nF, V
G
= 0V, R
G
= 0Ω, (See Figure 2) 25 - -44 - pC
OFF Isolation R
L
= 50Ω, C
L
= 5pF, f = 100kHz, V
COM
= 1V
RMS
,
(See Figure 4)
25 - 68 - dB
Crosstalk (Channel-to-Channel) R
L
= 50Ω, C
L
= 5pF, f = 100kHz, V
COM
= 1V
RMS
,
(See Figure 6)
25 - -98 - dB
NO or NC OFF Capacitance, C
OFF
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7) 25 - 106 - pF
COM ON Capacitance, C
COM(ON)
f = 1MHz, V
NO
or V
NC
= V
COM
= 0V, (See Figure 7) 25 - 212 - pF
Electrical Specifications - 3V Supply Test Conditions: V+ = +2.7V to +3.3V, GND = 0V, V
INH
= 1.4V, V
INL
= 0.5V (Notes 4, 6),
Unless Otherwise Specified (Continued)
PARAMETER TEST CONDITIONS
TEMP
(°C)
(NOTE 5)
MIN TYP
(NOTE 5)
MAX UNITS
ISL83699
