DSS1NB32A223Q91A Datasheet DSS1NB32A332Q91A, DSS1NB32A220Q91A, DSS1NB31H333Q91A | P7-P9

Spec No. JENF243F-0031A-01 P7/10

MURATA MFG.CO., LTD

Reference Only

10. Taping

(1) A maximum of 0.3% of the components quantity per Ammo pack may be missing without consecutive

missing components.

(2) The adhesive power of the tape shall have over 2.94N at the following condition.

(3) Splicing method of tape

1. Carrier tape

Carrier tape shall be spliced by cellophane tape.

Overall thickness shall be less than 1.05 mm.

(in mm)

2. Hold down tape

Hold down tape shall be spliced with overlapping.

Overall thickness shall be less than 1.05 mm.

(in mm)

3. Both carrier tape and hold down tape

Both tapes shall be cut zigzag and spliced with splicing tape.

11. Packing

11.1 Packing quantity

The standard packing quantity is as follows.

(The packing quantity may be changed due to a fraction of order.)

Minimun Packing Form and Quantity

Terminal Configuration A Unit Quantity Packing Form

∗ Standard Quantity

in a container

(corrugated cardboard box)

Bulk 250 pcs. In a plastic bag 5000pcs.

Taping

1500 pcs.

In an Ammo pack 7500pcs.

∗ A quantity in a container is depending on a quantity of an order.

11.2 Packing Form

(1) Bulk

1.Products are packed into a plastic bag. 2.The plastic bags are put into a container

(corrugated cardboard box) depending on a

quantity of an order.

Hold down tape

Carrier tape

2.94 N

30 to 50

Hold down tape

Carrier tape

Cellophane tape

Direction of feed

Overall thickness

Direction of feed

20 to 30

Hold down tape

Carrier tape

Overall thickness



a plastic bag

container label

a container

the plastic bag with products

Spec No. JENF243F-0031A-01 P8/10

MURATA MFG.CO., LTD

Reference Only

(2) Taping

1 .Folding the tape per 25 pitches,products are packed into an ammo package so that each product of each

layer wound zigzag is put on top of one another. [Fig 3]

2. The dimensions of the ammo package are indicated in [Fig 4].

3. The ammo packages are put into a container (corrugated cardboard box) depending on a quantity of an

order.

4. Not less than 3 consecutive of component shall be missing on both edge of tape.

[Fig 3] [Fig 4]

The unloading direction : Right

The hold down tape : Upper (in mm)

The product body : Left along the unloading direction

12. Marking on package

12.1 Unit Package

Bulk : Marked on a plastic bag.

Taping : Marked on a label stuck on an ammo package.

Marking on a unit package consists of :

Customer part number, MURATA part number, Inspection number(∗1), RoHS marking (∗2), Quantity, etc

∗1) « Expression of Inspection No. » □□

OOOO ×××

(1) (2) (3)

(1)

Factory Code

(2) Date First digit : Year / Last digit of year

Second digit : Month / Jan. to Sep. → 1 to 9, Oct. to Dec. → O,N,D

Third, Fourth digit : Day

(3) Serial No.

∗2) « Expression of RoHS marking » ROHS – Y

(△)

(1) (2)

(1)

RoHS regulation conformity parts.

(2) MURATA classification number

12.2 Container

Marking on the label stuck on a container consists of :

Customer name Purchasing Order Number, Customer Part Number, MURATA part number,

RoHS marking (∗2), Quantity, etc

13. △

Caution

13.1 Mounting holes

Mounting holes should be designed as specified in this specifications.

Or different design from this specifications may cause cracks in ceramics which may lead to smoking / firing.

13.2 Caution for the product angle adjust work

Take care not to apply any mechanical stress to product body at the lead terminal bending process for product

angle adjustment after insertion.

13.3 Limitation of Applications

Please contact us before using our products for the applications listed below which require especially high

reliability for the prevention of defects which might directly cause damage to the third party's life, body or

property.

(1) Aircraft equipment (7) Traffic signal equipment

(2) Aerospace equipment (7) Disaster prevention / crime prevention equipment

(3) Undersea equipment (9) Data-processing equipment

(4) Power plant control equipment (10) Applications of similar complexity and /or reliability requirements

(5) Medical equipment

to the applications listed in the above

(6) Transportation equipment (vehicles, trains, ships, etc.)

zig zag

label

340 max.

240 max.

51 max.

Spec No. JENF243F-0031A-01 P9/10

MURATA MFG.CO., LTD

Reference Only

14. Notice

14.1 Soldering

(1) Use rosin-based flux. Do not use strong acidic flux with halide content exceeding 0.2(wt)%

(chlorine conversion value).

Use Sn-3.0Ag-0.5Cu solder

(2) Standard flow soldering profile.

Solde

temperature

Soldering

time

250～260 °C 4～6s

(3) Resistance to soldering iron goes in the following condition that tip temperature is 350 °C max. And

soldering time is 5 s max.

(4) Products and the leads should not be subjected to any mechanical stress during soldering process.

(and also while subjected to the equivalent high temperature.)

14.2 Cleaning

Products shall be cleaned on following conditions.

(1) Cleaning Temperature: 60℃ max.(40℃ max. for Isopropyl alcohol).

(2) Ultrasonic cleaning shall comply with the following conditions, avoiding the resonance phenomenon at the

mounted products and P.C.B.

Power：20W / l max.

Frequency：28kHz ∼ 40kHz

Time ：5 minutes max.

(3) Cleaning agent

1. alcohol cleaning agents.

・Isopropyl alcohol (IPA)

2. Aqueous cleaning agent

・Pine Alpha ST-100S

(4) Ensure that residual flux and residual cleaning agent is completely removed.

Products should be thoroughly dried after aqueous agent has been removed with de-ionized water.

(5) For other cleaning methods, please contact Murata engineering.

14.3 Operating Environment

(1) Do not use products in corrosive gases such as chlorine gas, acid or sulfide gas.

(2) Do not use products in the environment where water, oil or organic solvents may adhere to products.

(3) Do not adhere any resin to products, coat nor mold products with any resin (including adhesive)to prevent

mechanical and chemical stress on products.

14.4 Storage and handling requirements.

(1) Storage period

Use the products within 12 months after delivered.

Solderability should be checked if this period is exceeded.

(2) Storage environment condition

To prevent products quality deterioration, stored conditions should be controlled as follows ;

1. Temperature : -10 to 40 degrees centigrade

2. Humidity : 15 to 85% relative humidity

3. Products should be stored without sudden changes in temperature and humidity.

Don't keep products in corrosive gases such as sulfur,chlorine gas or acid,

or it may cause oxidization of lead terminals resulting in poor solderability.

4. Products should be stored on the palette for the prevention of the influence from humidity, dust and so

on.

5. Products should be stored in the warehouse without heat shock, vibration,direct sunlight and so on.

(3) Handling Conditions

Care should be taken when transporting or handling product to avoid excessive vibration or

mechanical shock.

1 minutes min.

Soldering time

Solder temp.

250

200

150

100

Temperature (°C)

Pre- heating(in air)

Soldering

Gradual Cooling

(in air)

300

P1-P3 P4-P6 P7-P9 P10-P10

DSS1NB32A223Q91A

Mfr. #:

Buy DSS1NB32A223Q91A

Manufacturer:

Description:

Feed Through Capacitors 22000pF 6A 100volts +/-10% -40+85C

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

DSS1NB32A223Q91A

DSS1NB32A223Q91A

Products related to this Datasheet