3
LT1097
ELECTRICAL CHARACTERISTICS
V
S
= ±15V, V
CM
= 0V, 0°C ≤ T
A
≤ 70°C, unless otherwise noted.
LT1097CN8 LT1097S8
SYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
V
OS
Input Offset Voltage ● 20 100 20 130 µV
Average Temperature Coefficient of (Note 4) ● 0.2 1 0.2 1.4 µV/°C
Input Offset Voltage
I
OS
Input Offset Current ● 60 430 75 570 pA
Average Temperature Coefficient of (Note 4) ● 0.4 4 0.5 5 pA/°C
Input Offset Current
I
B
Input Bias Current ● ±60 ±430 ±75 ±570 pA
Average Temperature Coefficient of (Note 4) ● 0.4 4 0.5 5 pA/°C
Input Bias Current
A
VOL
Large Signal Voltage Gain V
OUT
= ±12V, R
L
≥ 10k ● 450 2000 450 2000 V/mV
V
OUT
= ±10V, R
L
≥ 2k ● 180 800 180 800 V/mV
CMRR Common Mode Rejection Ratio V
CM
= ±13.5V ● 112 128 112 128 dB
PSRR Power Supply Rejection Ratio V
S
= ±1.3V to ±20V ● 111 128 111 128 dB
Input Voltage Range ● ±13.5 ±14.2 ±13.5 ±14.2 V
V
OUT
Output Voltage Swing R
L
= 10k ● ±13 ±13.7 ±13 ±13.7 V
I
S
Supply Current ● 380 700 380 700 µA
ELECTRICAL CHARACTERISTICS
V
S
= ±15V, V
CM
= 0V, –40°C ≤ T
A
≤ 85°C, unless otherwise noted. (Note 5)
LT1097CN8 LT1097S8
SYMBOL PARAMETER CONDITIONS MIN TYP MAX MIN TYP MAX UNITS
V
OS
Input Offset Voltage ● 25 130 30 170 µV
Average Temperature Coefficient of ● 0.3 1.2 0.3 1.6 µV/°C
Input Offset Voltage
I
OS
Input Offset Current ● 70 600 85 750 pA
Average Temperature Coefficient of ● 0.5 5 0.6 6 pA/°C
Input Offset Current
I
B
Input Bias Current ● ±70 ±600 ±85 ±750 pA
Average Temperature Coefficient of ● 0.5 5 0.6 6 pA/°C
Input Bias Current
A
VOL
Large Signal Voltage Gain V
OUT
= ±12V, R
L
≥ 10k ● 300 1700 300 1700 V/mV
V
OUT
= ±10V, R
L
≥ 2k ● 700 700 V/mV
CMRR Common Mode Rejection Ratio V
CM
= ±13.5V ● 108 127 108 127 dB
PSRR Power Supply Rejection Ratio V
S
= ±1.5V to ±20V ● 108 127 108 127 dB
Input Voltage Range ● ±13.5 ±14 ±13.5 ±14 V
V
OUT
Output Voltage Swing R
L
= 10k ● ±13 ±13.6 ±13 ±13.6 V
I
S
Supply Current ● 400 800 400 800 µA
The ● denotes specifications which apply over the full operating
temperature range.
Note 1: Differential input voltages greater than 1V will cause excessive
current to flow through the input protection diodes unless limiting
resistance is used.
Note 2: This parameter is guaranteed by design and is not tested.
Note 3: Power supply rejection ratio is measured at the minimum supply
voltage.
Note 4: This parameter is not 100% tested.
Note 5: The LT1097 is designed, characterized and expected to meet these
extended temperature limits, but is not tested at –40°C and 85°C.
Guaranteed I grade parts are available; consult factory.