7
LT1632/LT1633
sn1632 16323fs
ELECTRICAL CHARACTERISTICS
–40°C < T
A
< 85°C, V
S
= ±15V, V
CM
= 0V, V
OUT
= 0V, unless otherwise noted. (Note 4)
SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS
V
OS
Input Offset Voltage V
CM
= V
+
– 0.1V ● 1000 3000 µV
V
CM
= V
–
+ 0.2V ● 1000 3000 µV
V
OS
TC Input Offset Voltage Drift (Note 3) ● 10 17 µV/°C
V
CM
= V
+
– 0.1V ● 511 µV/°C
∆V
OS
Input Offset Voltage Shift V
CM
= V
–
+ 0.2V to V
+
– 0.1V ● 500 2600 µV
Input Offset Voltage Match (Channel-to-Channel) V
CM
= V
–
+ 0.2V, V
+
– 0.1V
(Note 5) ● 850 4000 µV
I
B
Input Bias Current V
CM
= V
+
– 0.1V ● 0 1.4 2.8 µA
V
CM
= V
–
+ 0.2V ● –2.8 –1.4 0 µA
∆I
B
Input Bias Current Shift V
CM
= V
–
+ 0.2V to V
+
– 0.1V ● 2.8 5.6 µA
Input Bias Current Match (Channel-to-Channel) V
CM
= V
+
– 0.1V (Note 5) ● 75 1120 nA
V
CM
= V
–
+ 0.2V (Note 5) ● 75 1120 nA
I
OS
Input Offset Current V
CM
= V
+
– 0.1V ● 60 560 nA
V
CM
= V
–
+ 0.2V ● 60 560 nA
∆I
OS
Input Offset Current Shift V
CM
= V
–
+ 0.2V to V
+
– 0.1V ● 120 1120 nA
A
VOL
Large-Signal Voltage Gain V
O
= –14.5V to 14.5V, R
L
= 10k ● 500 5000 V/mV
V
O
= –10V to 10V, R
L
= 2k ● 250 1800 V/mV
Channel Separation V
O
= –10V to 10V, R
L
= 2k ● 110 124 dB
CMRR Common Mode Rejection Ratio V
CM
= V
–
+ 0.2V to V
+
– 0.1V ● 81 96 dB
CMRR Match (Channel-to-Channel)
(Note 5) V
CM
= V
–
+ 0.2V to V
+
– 0.1V ● 77 95 dB
PSRR Power Supply Rejection Ratio V
S
= ±5V to ±15V ● 80 93 dB
PSRR Match (Channel-to-Channel) (Note 5) V
S
= ±5V to ±15V ● 74 95 dB
V
OL
Output Voltage Swing Low (Note 6) No Load ● 23 50 mV
I
SINK
= 5mA ● 187 350 mV
I
SINK
= 25mA ● 700 1400 mV
V
OH
Output Voltage Swing High (Note 6) No Load ● 16 40 mV
I
SOURCE
= 5mA ● 300 600 mV
I
SOURCE
= 25mA ● 1500 3000 mV
I
SC
Short-Circuit Current ● ±27 ±54 mA
I
S
Supply Current per Amplifier ● 5.3 7 mA
GBW Gain-Bandwidth Product (Note 7) f = 100kHz ● 20 40 MHz
SR Slew Rate A
V
= –1, R
L
= Open, V
O
= ±10V, ● 18 35 V/µs
Measure at V
O
= ±5V
Note 5: Matching parameters are the difference between amplifiers A and
D and between B and C on the LT1633; between the two amplifiers on the
LT1632.
Note 6: Output voltage swings are measured between the output and
power supply rails.
Note 7: V
S
= 3V, V
S
= ±15V GBW limit guaranteed by correlation to
5V tests.
Note 8: V
S
= 3V, V
S
= 5V slew rate limit guaranteed by correlation to
±15V tests.
Note 9: Minimum supply voltage is guaranteed by testing the change of
V
OS
to be less than 250µV when the supply voltage is varied from 3V to
2.7V.
The
● denotes specifications that apply over the full operating temperature
range.
Note 1: Absolute Maximum Ratings are those values beyond which the life
of a device may be impaired.
Note 2: A heat sink may be required to keep the junction temperature
below the absolute maximum rating when the output is shorted
indefinitely.
Note 3: This parameter is not 100% tested.
Note 4: The LT1632C/LT1633C are guaranteed to meet specified
performance from 0°C to 70°C and are designed, characterized and
expected to meet these extended temperature limits, but are not tested at
–40°C and 85°C. Guaranteed I grade parts are available, consult factory.