WT30-FT001 Datasheet WT30-M01-FLK, WT30-SMD16, WT30-SMD16-1 | P1-P3

FA Wireless SS Terminals WT30 1

FA Wireless SS Terminals

WT30

Construct a Wireless System for ON/OFF

Data Collection That Is Ideal for Monitoring

Production Site Equipment

• Wireless Slave Station equipped with I/O.

• Height of 90 mm and DIN Rail mounting enables installation in

control panels.

• Easily check wireless communications status from indicator

display.

• I/O Slave Stations can also be used as Slave Stations in WD30

systems.

• Conforms to radio wave standards for Japan, China (pending),

USA, and Europe.

Ordering Information

■ List of Models

Note: An Antenna and Mounting Brackets are not included with the Wireless SS Terminal.

■ Accessories

Antennas

Communications Cables

Other

Applicable Standards

• FCC part 15.247 (USA)

• EN 300 440-2 (Europe)

• ARIB STD-T66 (Japan)

• (China) (approval pending)

Main Class 2 Power Supplies

OMRON Switching Power Supplies

• S8VS (15 W, 30 W, 60 W type)

• S82K (15 W, 30 W, 50 W, 90 W type)

Applicable Countries

Wireless standards have been met for the following countries. The

product cannot be used in any other countries.

Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia,

Finland, France, Germany, Greece, Hungry, Iceland, Ireland, Italy,

Japan, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,

Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland,

UK, USA

Wireless Unit model Type Specifications/No. of I/O points

WT30-M01-FLK Serial master RS-232C

WT30-SID16 I/O slaves 16 DC inputs (NPN/PNP)

WT30-SMD16 8 DC inputs (NPN/PNP) + 8 transistor outputs (NPN)

WT30-SMD16-1 8 DC inputs (NPN/PNP) + 8 transistor outputs (PNP)

Model Type

WT30-AT001 Magnet-base Antenna (2 antennas per set)

WT30-AT002 Flat Diversity Antenna (1 antenna)

WT30-AT003 Pencil Antenna (2 antennas per set)

Model Length Application

XW2Z-0100U-3 1 m For personal computer

XW2Z-0200U-3 2 m

XW2Z-0500U-3 5 m

XW2Z-0200U-5 2 m Cross cable for PLC

XW2Z-0500U-5 5 m

Model Type

WT30-FT001 DIN Rail Mounting Bracket (for TH35-7.5)

WT30-FT002 DIN Rail Mounting Bracket (for TH35-15)

WT30-FT003 Surface Mounting Bracket (screw-mounting)

(2 brackets per set)

WT30-FT011 Flat Diversity Antenna Mounting Brackets

(with magnets)

WT30-CA2M Antenna Extension Cable (1 cable, 2 m)

Conformity to Safety Standards

Always use a Class 2 power supply to conform to UL standards.

Conformity to EN Standards

Use a DC power line less than 3 m to conform to EN standards. If a

power line of 3 m or longer is required, extend the length at the

Switching Power Supply’s primary side (i.e., the AC power line).

2 FA Wireless SS Terminals WT30

Specifications

■ Ratings

Note: 1. Provide a power supply of at least 15 W, considering the inrush current generated at startup.

2. Use the WT30-FT003 Surface Mounting Bracket when installing the WT30 in environments subject to vibration.

■ Wireless Interface Specifications

Note: Varies according to the installation environment.

■ Package Contents

• WT30 FA Wireless SS Terminal • Terminal labels (I/O Slaves only)

• Instruction Sheet • Adhesive non-slip feet (Serial Master only)

Item WT30-M01-FLK Serial Master WT30-SID16/SMD16/SMD16-1 I/O Slaves

Power supply

(wireless

communications

power supply)

Rated voltage 24 V DC

Allowable voltage

range

20.4 to 26.4 V DC

Power consumption 3 W max. (See note 1.)

Error output/output

power supply

(for output circuits)

Rated voltage --- 24 V DC

Allowable voltage

range

--- 20.4 to 26.4 V DC

Insulation resistance 20 M

Ω min. (at 100 V DC) between the power

supply and chassis

20 MΩ min. (at 100 V DC) between the power

supply and all I/O and I/O power supply and

between the power supply and chassis

Dielectric strength 1,500 V AC for 1 min between power supply

and chassis

1,500 V AC for 1 min between the power supply

and all I/O and I/O power supply and between

the power supply and chassis

Noise immunity IEC61000-4-4. 1 kV (power supply line)

Vibration resistance (See note 2.) JIS C0040

Frequency: 10 to 55 Hz; Amplitude of 0.35 mm or acceleration of 50 m/s

, whichever is smaller

(DIN Rail mounting: single amplitude of 0.1 mm or acceleration of 15 m/s

)

10 sweeps of 8 min each (i.e., 80 min in total) in X, Y, Z directions

Shock resistance

Conforms to JIS C0041: 300 m/s

3 times each in X, Y, and Z directions

Ambient operating temperature

−10 to 55°C (with no condensation or icing)

(with the Terminal mounted with the dust-proof

label facing up)

Number of simultaneously ON I/O points

10 max.:

−10 to 55°C (with no condensation or

icing)

16 max.:

−10 to 50°C (with no condensation or

icing)

(with the Terminal mounted with the dust-proof

label facing up)

Ambient operating humidity 25% to 85% (with no condensation or icing)

Ambient environment No corrosive gases

Storage temperature

−25 to 65°C (with no condensation or icing)

Protective structure IP20

Terminal construction Power supply and I/O Screwless terminal block (Phoenix Contact FFKDS/V1-5.08 or equivalent)

Serial D-sub, 9-pin (female) Inch screws (OMRON

XM2F-0910-132 or equivalent), Master station

only

---

Safety standards UL: UL508 (Listing)

Weight 330 g max.

Item Specifications

Wave type Spread Spectrum (direct sequence; DS-SS)

Communication method Simplex

Frequency band 2,401 to 2,480.2 MHz

Number of channels 67 channels (based on switching)

Transmitter output power 10 mW/MHz

Baud rate between wireless stations 100 kbps

Communications distance (See note.) Indoors: 60 m min. (approx. 50 m min. with Magnet-base Antennas and Flat Diversity Antennas)

Outdoors: Approx. 300 m min. (anticipated distances)

(without using relay stations)

Error detection method CRC-CCITT (16 bits)

Relay functions One stage using I/O slave for the serial master configuration.

Number of stations per area (See note.) 10 sets max. (recommended)

Number of I/O Slaves connected 64 max.

FA Wireless SS Terminals WT30 3

Nomenclature

■ Serial Master Station

■ I/O Slave Station

■ Unit No. Switch

Set the unit number of the Serial Master Station

Default: 00

■ Node Setting Switch (WNODE)

Set the number of connected I/O Slave Stations.

Set the node number of the Slave Stations being used as I/O Slave

Stations. The Slave Station functions as a relay station when the

node number is set to 99.

Default: 01

■ Channel Setting Switch (WCH)

Set the communications frequency.

Default: 02

■ Function Setting Switch

Serial Master Station

I/O Slave Station

Antenna terminal (ANT1)

Status

indicators

RS-232C Terminal

Connect the PLC, personal computer, etc.

Power supply terminal

Supply power to the WT30.

Unit No. switch

Set the unit number of the Serial Master Station.

Node setting switch (WNODE)

Set the number of connected I/O Slave Stations.

Channel setting switch (WCH)

Set the communications frequency

channel.

Antenna terminal (ANT2)

Received

signal

strength

indicator

Special

function

switch

Function setting switch

Make the detailed settings

for RUN/TEST/SET mode.

Mode selection switch

Switch between RUN,

TEST, and SET mode.

Serial communications

setting switch

Set the baud rate.

Status

indicators

Power supply terminal

Supply power to the WT30

and output circuits.

Mode selection switch

Switch between RUN,

TEST, and SET mode.

Node setting switch (WNODE)

Set the unit number of the I/O Slave Station.

I/O terminal status indicators (0 to 7 or 8 to 15)

The contact status is displayed.

Channel setting switch (WCH)

Set the communications frequency.

Antenna terminal (ANT2)

Received

signal

strength

indicator

Special function switch

Antenna terminal (ANT1)

Function setting switch

Make the detailed settings

for RUN/TEST mode.

I/O terminals

Connect the contact

signals.

No. Applicable

mode

ON functions OFF functions

1 RUN mode Holds I/O status data

when a

communications error

occurs.

Clears I/O status data

when a

communications error

occurs.

2 Enable scan list Disable scan list

3 Relays used Relays not used

4 TEST mode Signal strength monitor

disabled

Signal strength monitor

enabled

5 All channels

automatically switched

Specified channels

6 --- ---

7 SET mode Scan list recognition Nothing done

8 Registers specified I/O

slave

Registers all I/O slaves

automatically

9 Recognizes serial

numbers

Ignores serial numbers

10 Not used --- ---

No. Applicable

mode

ON functions OFF functions

1 RUN mode Holds I/O status data

when a

communications error

occurs.

Clears I/O status data

when a

communications error

occurs.

2 Input hold Normal mode

3 Input filter: 100 ms Input filter: 10 ms

4 TEST mode Signal strength monitor

disabled

Signal strength monitor

enabled

5 All channels

automatically switched

Specified channels

6 Installation test

function

Nothing done

7 to

Not used --- ---

P1-P3 P4-P6 P7-P8

WT30-FT001

Mfr. #:

Buy WT30-FT001

Manufacturer:

Omron Automation and Safety

Description:

RF Modules DIN Rail MntBrk t(for TH357.5)

Lifecycle:

New from this manufacturer.

Delivery:

DHL FedEx Ups TNT EMS

Payment:

T/T Paypal Visa MoneyGram Western Union

WT30-FT001

WT30-FT001

Products related to this Datasheet