OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

RC1280

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P26
Radiocrafts
Embedded Wireless Solutions
RC1240/1280/1290
©2011 Radiocrafts AS RC1240/RC1280/RC1290 Data Sheet (rev. 1.62) Page 22 of 26
If a detachable RF connector is introduced in RF path it must be a non-standard type RP-
SMA, U.Fl etc. The modules have been approved with the following external quarter wave
antennas:
Part number Manufacturer Specified gain Connenctor
W915-RS EAD 3.0 dBi RP-SMA
MWR915-RS EAD 2.0 dBi RP-SMA
WR868(FWR835021-
RS-RA)
EAD 1.0 dBi RP-SMA
WS868(FWS835021-
RS-RA) EAD 1.0 dBi RP-SMA
ISM915/B/SMA/RP90 Cti 2.0 dBi RP-SMA
ISM915/B/SMA/RP Cti 2.0 dBi RP-SMA
Any use of antenna with gain > 3 dBi is strictly forbidden.
The output power of RC1290 is below the FCC threshold requiring that it be tested for SAR
compliance.
La puissance de sortie du RC1290 est inférieur au seuil FCC nécessitant que des tests de
conformité SAR soient réalisés.
This device has been designed to operate with an quarter wave antenna having a maximum
gain of 3 dBi. Antenna having a higher gain is strictly prohibited per regulations of Industry
Canada. The required antenna impedance is 50 ohms.
Cet appareil a été conçu pour fonctionner avec une antenne 1/ d'ondes ayant un gain
maximum de 3 dBi. Utiliser une antenne à gain plus élevé est strictement interdite par les
règlements d'Industrie Canada. L'impédance d'antenne requise est de 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be
so chosen that the equivalent isotropically radiated power (EIRP) is not more than that
required for successful communication.
Pour réduire le risque d'interférence pour les autres utilisateurs, le type d'antenne et son gain
doivent être choisies de façon que la puissance isotrope rayonnée équivalente (PIRE) n'est
pas supérieure à celle requise pour une communication réussie.
The installer of this radio equipment must ensure that the antenna is located or pointed such
that it does not emit RF field in excess of Health Canada limits for the general population;
consult Safety Code 6, obtainable from Health Canada’s website www.hc-sc.gc.ca/rpb
Le programme d'installation de cet équipement radio doit s'assurer que l'antenne est située
ou orientée de façon à ne pas émettre de champ RF dépassant les limites de Santé Canada
pour la population en général, consulter le Code de sécurité 6, disponible sur le site Web de
Santé Canada www.hc-sc.gc.ca/rpb
Radiocrafts
Embedded Wireless Solutions
RC1240/1280/1290
©2011 Radiocrafts AS RC1240/RC1280/RC1290 Data Sheet (rev. 1.62) Page 23 of 26
End product marking FCC/IC
The end product including RC1290 must include the following text on a visible label:
Contains Transmitter Module FCC ID: Y2NRC1290/IC: 9402A-RC1290
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Module transmetteur ID IC: 9402A-RC1290
Son fonctionnement est soumis aux deux conditions suivantes: (1) cet appareil ne doit pas
causer d'interférences nuisibles et (2) cet appareil doit accepter toute interférence reçue, y
com
p
ris les interférences
q
ui
p
euvent
p
erturber le fonctionnement.
Radiocrafts
Embedded Wireless Solutions
RC1240/1280/1290
©2011 Radiocrafts AS RC1240/RC1280/RC1290 Data Sheet (rev. 1.62) Page 24 of 26
Document Revision History
Document Revision Changes
1.0 First release
1.1 Data buffer length changed from 200 to 145
RC1240: Number of channels increased from 30 to 69
Sleep current typo corrected from 85 uA to 0.9 mA on first page
Active polarity and RESET added in pin description
1.2 Data buffer length changed from 145 to 128
Added more information in the Pin description
Added PCB layout recommendation
Added carrier tape and reel specification
Digital I/O specifications added in Electrical Specifications
Updated Electrical Specifications
Added timing information
Added RSSI data
Minor corrections for clarity
1.3 Timing information changed according to latest firmware upgrade (rev 1.16
and later)
Minor spelling errors corrected, clarifications added
Emphasized that some digital I/Os have 100 kOhm series resistors
Note on VCC rise-time in the Power Management section
Pin description for PA_EN and LNA_EN added
New section on external PA and LNA control added
Spurious emission in TX corrected in Electrical Specifications
Added more information on power-on-reset when using ON/OFF
1.4 Power Management: Corrected reset signal series resistor value from
100kOhm to 10kOhm
Timing Information: Added a note on periodic recalibration of UART time base
1.5 Added timing info on Config pin low to prompt
Updated product status to Full Production
1.61 Added pin description equivalent circuits
Added UART baud rate tolerance specification
Added soldering profile recommendation
Added note on 2 stop-bits if CTS is used
Added note on RSSI measurement is followed by a new prompt
Added note on delay after channel-byte in timing information
Added configuration memory write cycle specification, and note in the text
Added new section and more information on Power on Reset and reset
circuits
Added new section and more information on I/O pin interfaces
Added more info on ON/OFF in pin description
Added note on digital signal output level and level translators
Added new section on regulatory compliance information
Clarified awakening from SLEEP mode using RXEN and TXEN
Clarified Product Status and Definition
Clarified layout recommendations
1.62 Added FCC/IC info regarding RC1290.
Adjusted output power based on statistics
Updated solder recommendation to new JEDEC/IPC standard.
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21P22-P24P25-P26

RC1280

Mfr. #:
Buy RC1280
Manufacturer:
Description:
NARROWBAND 868-870
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet