MC100E241
http://onsemi.com
3
Table 3. MAXIMUM RATINGS
Symbol Parameter Condition 1 Condition 2 Rating Unit
V
CC
PECL Mode Power Supply V
EE
= 0 V 8 V
V
EE
NECL Mode Power Supply V
CC
= 0 V −8 V
V
I
PECL Mode Input Voltage
NECL Mode Input Voltage
V
EE
= 0 V
V
CC
= 0 V
V
I
v V
CC
V
I
w V
EE
6
−6
V
V
I
out
Output Current Continuous
Surge
50
100
mA
mA
T
A
Operating Temperature Range 0 to +85 °C
T
stg
Storage Temperature Range −65 to +150 °C
q
JA
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
PLCC−28
PLCC−28
63.5
43.5
°C/W
°C/W
q
JC
Thermal Resistance (Junction−to−Case) Standard Board PLCC−28 22 to 26 °C/W
T
sol
Wave Solder Pb
Pb−Free
265
265
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
Table 4. 100E SERIES PECL DC CHARACTERISTICS V
CCx
= 5.0 V, V
EE
= 0.0 V (Note 1)
Symbol
Characteristic
0°C 25°C 85°C
Unit
Min Typ Max Min Typ Max Min Typ Max
I
EE
Power Supply Current 125 150 125 150 144 173 mA
V
OH
Output HIGH Voltage (Note 2) 3975 4050 4120 3975 4050 4120 3975 4050 4120 mV
V
OL
Output LOW Voltage (Note 2) 3190 3295 3380 3190 3255 3380 3190 3260 3380 mV
V
IH
Input HIGH Voltage 3835 3975 4120 3835 3975 4120 3835 3975 4120 mV
V
IL
Input LOW Voltage 3190 3355 3525 3190 3355 3525 3190 3355 3525 mV
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current 0.5 0.3 0.5 0.25 0.5 0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary −0.46 V / +0.8 V.
2. Outputs are terminated through a 50 W resistor to V
CC
− 2.0 V.
Table 5. 100E SERIES NECL DC CHARACTERISTICS V
CCx
= 0.0 V; V
EE
= −5.0 V (Note 3)
Symbol
Characteristic
0°C 25°C 85°C
Unit
Min Typ Max Min Typ Max Min Typ Max
I
EE
Power Supply Current 125 150 125 150 144 173 mA
V
OH
Output HIGH Voltage −1025 −950 −880 −1025 −950 −880 −1025 −950 −880 mV
V
OL
Output LOW Voltage −1810 −1705 −1620 −1810 −1745 −1620 −1810 −1740 −1620 mV
V
IH
Input HIGH Voltage (Single−Ended) −1165 −1025 −880 −1165 −1025 −880 −1165 −1025 −880 mV
V
IL
Input LOW Voltage (Single−Ended) −1810 −1645 −1475 −1810 −1645 −1475 −1810 −1645 −1475 mV
I
IH
Input HIGH Current 150 150 150
mA
I
IL
Input LOW Current 0.5 0.3 0.5 0.25 0.5 0.2
mA
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
3. Input and output parameters vary 1:1 with V
CC
. V
EE
can vary −0.46 V / +0.8 V.
4. Outputs are terminated through a 50 W resistor to V
CC
− 2.0 V.
