OMO ElectronicOMO Electronic
Expand menu
Hello, Sign inMy Account
0 Cart

ADUM230E1BRIZ-RL

P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21
Data Sheet ADuM230D/ADuM230E/ADuM231D/ADuM231E
Rev. A | Page 7 of 21
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
AC SPECIFICATIONS
Output Rise/Fall Time t
R
/t
F
2.5 ns 10% to 90%
Common-Mode Transient Immunity
7
|CM
H
| 75 100 kV/µs
V
Ix
= V
DDx
, V
CM
= 1000 V,
transient magnitude = 800 V
|CM
L
| 75 100 kV/µs
V
Ix
= 0 V, V
CM
= 1000 V,
transient magnitude = 800 V
1
150 Mbps is the highest data rate that can be guaranteed, although higher data rates are possible.
2
I
Ox
is the Channel x output current, where x = A, B, or C.
3
V
IxH
is the input side logic high.
4
V
IxL
is the input side logic low.
5
V
I
is the voltage input.
6
E0 refers to the ADuM230E0/ADuM231E0 models, D0 refers to the ADuM230D0/ADuM231D0 models, E1 refers to the ADuM230E1/ADuM231E1 models, and D1 refers
to the ADuM230D1/ADuM231D1 models. See the Ordering Guide section.
7
|CM
H
| is the maximum common-mode voltage slew rate that can be sustained while maintaining the voltage output (V
Ox
) > 0.8 V
DDx
. |CM
L
| is the maximum common-
mode voltage slew rate that can be sustained while maintaining V
Ox
> 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode
voltage edges.
Table 6. Total Supply Current vs. Data Throughput
1 Mbps 25 Mbps 100 Mbps
Parameter Symbol Min Typ Max Min Typ Max Min Typ Max Unit
SUPPLY CURRENT
ADuM230D/ADuM230E
Supply Current Side 1 I
DD1
5.3 8.7 5.9 9.3 8.2 12.3 mA
Supply Current Side 2 I
DD2
1.8 3.6 2.6 4.4 5.2 7.4 mA
ADuM231D/ADuM231E
Supply Current Side 1 I
DD1
4.4 7.1 5.0 7.8 7.5 10.1 mA
Supply Current Side 2 I
DD2
3.4 5.6 4.1 6.3 6.6 8.7 mA
ELECTRICAL CHARACTERISTICS—1.8 V OPERATION
All typical specifications are at T
A
= 25°C, V
DD1
= V
DD2
= 1.8 V. Minimum/maximum specifications apply over the entire recommended
operation range: 1.7 V ≤ V
DD1
≤ 1.9 V, 1.7 V ≤ V
DD2
≤ 1.9 V, and −40°C ≤ T
A
≤ +125°C, unless otherwise noted. Switching specifications
are tested with C
L
= 15 pF and CMOS signal levels, unless otherwise noted. Supply currents are specified with 50% duty cycle signals.
Table 7.
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
SWITCHING SPECIFICATIONS
Pulse Width PW 6.6 ns Within PWD limit
Data Rate
1
150 Mbps Within PWD limit
Propagation Delay t
PHL
, t
PLH
5.8 8.7 15 ns 50% input to 50% output
Pulse Width Distortion PWD 0.7 3 ns |t
PLH
− t
PHL
|
Change vs. Temperature 1.5 ps/°C
Propagation Delay Skew t
PSK
7.0 ns
Between any two devices at the same
temperature, voltage, and load
Channel Matching
Codirectional t
PSKCD
0.7 3.0 ns
Opposing Direction t
PSKOD
0.7 3.0 ns
Jitter 600 ps p-p See the Jitter Measurement section
90 ps rms See the Jitter Measurement section
DC SPECIFICATIONS
Input Threshold Voltage
Logic High V
IH
0.7 × V
DDx
V
Logic Low V
IL
0.3 × V
DDx
V
ADuM230D/ADuM230E/ADuM231D/ADuM231E Data Sheet
Rev. A | Page 8 of 21
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
Output Voltage
Logic High V
OH
V
DDx
− 0.1 V
DDx
V I
Ox
2
= −20 µA, V
Ix
= V
IxH
3
V
DDx
− 0.4 V
DDx
− 0.2 V I
Ox
2
= −2 mA, V
Ix
= V
IxH
3
Logic Low V
OL
0.0 0.1 V I
Ox
2
= 20 µA, V
Ix
= V
IxL
4
0.2 0.4 V I
Ox
2
= 2 mA, V
Ix
= V
IxL
4
Input Current per Channel I
I
−10 +0.01 +10 µA 0 V ≤ V
Ix
≤ V
DDx
V
E2
Enable Input Pull-Up Current I
PU
−10 −3 µA V
E2
= 0 V
DISABLE
1
Input Pull-Down Current I
PD
9 15 µA DISABLE
1
= V
DDx
Tristate Output Current per Channel I
OZ
−10 +0.01 +10 µA 0 V ≤ V
Ox
≤ V
DDx
Quiescent Supply Current
ADuM230D/ADuM230E
I
DD1 (Q)
1.15 2.3 mA V
I
5
= 0 (E0, D0), 1 (E1, D1)
6
I
DD2 (Q)
1.58 2.6 mA V
I
5
= 0 (E0, D0), 1 (E1, D1)
6
I
DD1 (Q)
9.41 14.8 mA V
I
5
= 1 (E0, D0), 0 (E1, D1)
6
I
DD2 (Q)
1.72 2.7 mA V
I
5
= 1 (E0, D0), 0 (E1, D1)
6
ADuM231D/ADuM231E
I
DD1 (Q)
1.42 2.4 mA V
I
5
= 0 (E0, D0), 1 (E1, D1)
6
I
DD2 (Q)
1.44 2.4 mA V
I
5
= 0 (E0, D0), 1 (E1, D1)
6
I
DD1 (Q)
7.15 11.1 mA V
I
5
= 1 (E0, D0), 0 (E1, D1)
6
I
DD2 (Q)
5.13 6.9 mA V
I
5
= 1 (E0, D0), 0 (E1, D1)
6
Dynamic Supply Current
Dynamic Input I
DDI (D)
0.01 mA/Mbps Inputs switching, 50% duty cycle
Dynamic Output I
DDO (D)
0.01 mA/Mbps Inputs switching, 50% duty cycle
Undervoltage Lockout UVLO
Positive V
DDx
Threshold V
DDxUV+
1.6 V
Negative V
DDx
Threshold V
DDxUV−
1.5 V
V
DDx
Hysteresis V
DDxUVH
0.1 V
AC SPECIFICATIONS
Output Rise/Fall Time t
R
/t
F
2.5 ns 10% to 90%
Common-Mode Transient Immunity
7
|CM
H
| 75 100 kV/µs
V
Ix
= V
DDx
, V
CM
= 1000 V,
transient magnitude = 800 V
|CM
L
| 75 100 kV/µs
V
Ix
= 0 V, V
CM
= 1000 V,
transient magnitude = 800 V
1
150 Mbps is the highest data rate that can be guaranteed, although higher data rates are possible.
2
I
Ox
is the Channel x output current, where x = A, B, or C.
3
V
IxH
is the input side logic high.
4
V
IxL
is the input side logic low.
5
V
I
is the voltage input.
6
E0 refers to the ADuM230E0/ADuM231E0 models, D0 refers to the ADuM230D0/ADuM231D0 models, E1 refers to the ADuM230E1/ADuM231E1 models, and D1 refers
to the ADuM230D1/ADuM231D1 models. See the Ordering Guide section.
7
|CM
H
| is the maximum common-mode voltage slew rate that can be sustained while maintaining the voltage output (V
Ox
) > 0.8 V
DDx
. |CM
L
| is the maximum common-
mode voltage slew rate that can be sustained while maintaining V
Ox
> 0.8 V. The common-mode voltage slew rates apply to both rising and falling common-mode
voltage edges.
Table 8. Total Supply Current vs. Data Throughput
1 Mbps 25 Mbps 100 Mbps
Parameter Symbol Min Typ Max Min Typ Max Min Typ Max Unit
SUPPLY CURRENT
ADuM230D/ADuM230E
Supply Current Side 1 I
DD1
5.2 8.6 5.8 9.3 8.1 12.2 mA
Supply Current Side 2 I
DD2
1.7 3.5 2.5 4.3 5.2 7.3 mA
ADuM231D/ADuM231E
Supply Current Side 1 I
DD1
4.3 7.0 4.9 7.7 7.26 10.0 mA
Supply Current Side 2 I
DD2
3.3 5.5 4.0 6.2 6.5 8.6 mA
Data Sheet ADuM230D/ADuM230E/ADuM231D/ADuM231E
Rev. A | Page 9 of 21
INSULATION AND SAFETY RELATED SPECIFICATIONS
For additional information, see www.analog.com/icouplersafety.
Table 9. RW-16 Wide Body [SOIC_W] Package
Parameter Symbol Value Unit Test Conditions/Comments
Rated Dielectric Insulation Voltage 5000 V rms 1-minute duration
Minimum External Air Gap (Clearance) L (I01) 7.8 mm min
Measured from input terminals to output terminals,
shortest distance through air
Minimum External Tracking (Creepage) L (I02) 7.8 mm min
Measured from input terminals to output terminals,
shortest distance path along body
Minimum Clearance in the Plane of the Printed
Circuit Board (PCB Clearance)
L (PCB) 8.1 mm min
Measured from input terminals to output terminals,
shortest distance through air, line of sight, in the PCB
mounting plane
Minimum Internal Gap (Internal Clearance) 25.5 m min Insulation distance through insulation
Tracking Resistance (Comparative Tracking Index) CTI >400 V DIN IEC 112/VDE 0303 Part 1
Material Group II Material Group (DIN VDE 0110, 1/89, Table 1)
Table 10. RI-16 -2 Wide Body Increased Creepage [SOIC_IC] Package
Parameter Symbol Value Unit Test Conditions/Comments
Rated Dielectric Insulation Voltage 5000 V rms 1-minute duration
Minimum External Air Gap (Clearance) L (I01) 8.3 mm min
Measured from input terminals to output terminals,
shortest distance through air
Minimum External Tracking (Creepage) L (I02) 8.3 mm min
Measured from input terminals to output terminals,
shortest distance path along body
Minimum Clearance in the Plane of the Printed
Circuit Board (PCB Clearance)
L (PCB) 8.3 mm min
Measured from input terminals to output terminals,
shortest distance through air, line of sight, in the PCB
mounting plane
Minimum Internal Gap (Internal Clearance) 25.5 m min Insulation distance through insulation
Tracking Resistance (Comparative Tracking Index) CTI >400 V DIN IEC 112/VDE 0303 Part 1
Material Group II Material Group (DIN VDE 0110, 1/89, Table 1)
PACKAGE CHARACTERISTICS
Table 11.
Parameter Symbol Min Typ Max Unit Test Conditions/Comments
Resistance (Input to Output)
1
R
I-O
10
13
Ω
Capacitance (Input to Output)
1
C
I-O
2.2 pF f = 1 MHz
Input Capacitance
2
C
I
4.0 pF
IC Junction to Ambient Thermal Resistance θ
JA
45 °C/W Thermocouple located at center of package underside
1
The device is considered a 2-terminal device: Pin 1 through Pin 8 are shorted together, and Pin 9 through Pin 16 are shorted together.
2
Input capacitance is from any input data pin to ground.
P1-P3P4-P6P7-P9P10-P12P13-P15P16-P18P19-P21

ADUM230E1BRIZ-RL

Mfr. #:
Buy ADUM230E1BRIZ-RL
Manufacturer:
Analog Devices Inc.
Description:
Digital Isolators IC Robust 3 ch ISO 3:0 ch
Lifecycle:
New from this manufacturer.
Delivery:
DHL FedEx Ups TNT EMS
Payment:
T/T Paypal Visa MoneyGram Western Union

Products related to this Datasheet